- Question categories:
- Architectural
- Automotive
- Tint & PPF Tools
- PPF
- Vinyl
What are some good tools to use for tinting a back window?
Answer 1: A titan squeegee is a great choice for water removal and features a rigid structure. Answer 2: Many tinters prefer to use the Bulldozer squeegee for back glass. Answer 3: The SideSwiper is a big favorite among tinters today for back glass windows.
How do you keep a car running for long periods of time without having to keep pressing the ignition every five minutes?
Answer 1: For cars with keyless ignition, you can keep the car running for up to five minutes by pressing the ignition button. However, the vehicle will automatically shut off after five minutes. However, if you actually hold down the ignition button, you get 40 minutes of runtime before the vehicle shuts off. This gives […]
How do you tint a Mooney M20R?
Answer 1: Check FAA rules before tinting, as you’ll need special film for plexiglass windows used on aircraft. Answer 2: You’ll need to use a special kind of film called “plane tint,” which is basically just tinted Paint Protection Film. Answer 3: Cut your film from the inside. Answer 4: Make sure […]
How do you tint a 2021 Tahoe?
Answer 1: Make sure to shrink the doors well. Answer 2: Preshrink the doors. Answer 3: You can take off the panels if you want for an easier installation process. Answer 4: Be on the lookout for gaps and dirt. Answer 5: Be aware that the glass on this vehicle is […]
How much does it cost to start a window tinting business?
Answer 1: Some tinters can start tinting businesses with as little as $1,000. Answer 2: It depends on whether you’re running the business out of your home. If so, you can simply purchase film and tools. If you’re planning on renting a separate space, you’ll need about $10,000 for rent, supplies, utilities, and deposits. […]
How do you tint the back window on the new Subaru Outback?
Answer 1: First, shrink the top. Then, pull the film up. Finally, shrink the bottom. Answer 2: You may need to remove the spoilers. There should be six bolts that hold the spoilers in place, and it should only take a few minutes to remove this component. You can tint with the spoiler still […]
Is there a type of film that can make your windows bulletproof?
Answer `: No. Do not believe companies that say they make bulletproof film. People have tested such productions and discovered that a .22 bullet can easily penetrate the window.
How do you cut a sun strip as straight as possible without a plotter?
Answer 1: Place a 12-inch piece of film on the roof and use the top of the windshield as a guide to create a curved edge. Answer 2: For most sedans and coupes, you can actually use the back glass as your guide. Answer 3: If the edge of the glass isn’t exposed, […]
How do you tint the back window of a 1984 Porsche 944?
Answer 1: You’ll need to remove the rear wing and the rear wiper. The rear wing can be a little tricky, as you’ll need to drill out a screw. Inform the customer before you do this, as they’ll need to retap the screw. Answer 2: You’ll need some black vinyl to cover the ceramic […]
What should you do if a customer complains about bubbles during the curing process?
Answer 1: Just tell them to leave it alone and keep the car in sunlight if possible. The bubbles should go away if the customer simply lets the car go through the normal curing process. Answer 2: This process can take much longer in the winter. Sometimes, it can take up to three weeks […]
What is the best way to tint a car as quickly as possible?
Answer 1: You might want to take your time, as rushing often leads to contaminated, messy results. Answer 2: Use the production line method. Instead of doing one window at a time, do each stage at a time. For example, cut everything first, then shrink, then install.
Which is the better technique: bottom-loading or the two-stage method?
Answer 1: Two-stage is typically faster, but it can be difficult to master. Even those who think they are doing this correctly are actually making mistakes without realizing it. Answer 2: Different techniques may be more effective for certain types of vehicles. This is why it’s important to become proficient in both methods. […]
What are some major issues with being a mobile tinter?
Answer 1: Working in dirty environments. Sometimes, you show up to somewhere like a welding shop where you can’t control the contamination in the air. Your best bet for situations like these is using a very clean water source with filtration. Answer 2: Mobile tinters often have to work in very tight spaces. This […]
How do you deal with the foam on Ford vehicles when working on the dot matrix?
Answer 1: These kinds of situations can be extremely tight. You can try to stuff a towel in the area to protect the vehicle, but the issue is that the towel may pull the film up when you remove it. Answer 2: A towel is not necessary for all Ford models. Many of the […]
Which is better, hand-cutting or using a plotter?
Answer 1: No single method is better than the other. In fact, most plotters agree that a mixture of both methods is necessary for a shop in today’s world. This is because there are many different types of vehicles, and your plotter might not have a pattern for a rare vehicle in its software library. […]
How can you make your cuts as precise as possible when hand-cutting?
Answer 1: One option is to use vinyl tape as a guide when cutting to make sure your lines are extremely straight. Answer 2: Get an extremely bright LED light and place it in the rear deck when cutting the rear window and windshields. Often, tinters make mistakes because they cannot really see what […]
Can you tint soft tops?
Answer 1: If the soft top is plastic, you’ll need to use tail light film. This is really the only viable option, and many tinters believe that it’s not worth the effort. This is because tail light vinyl typically offers poor levels of clarity and is quite expensive. In addition, mistakes can be costly. Replacing […]
How to avoid contamination on the roll-down front passenger windows with a Volvo 850?
Answer 1: Make sure to use the bottom-loading technique if possible. Answer 2: Be sure to pull the panels before installation to limit contamination. Answer 3: You should tape the seals if you want to limit contamination. Answer 4: Cut the sides a bit tighter than normal. This will ensure that you’re […]
How do you tint the back window on a newer Toyota hatchback?
Answer 1: Remove the panel on the hatch, and you’ll find that the entire process is much easier. The shrink should take only minutes. Answer 2: Shrink in quarter sections and use the regular roll-down technique. Make sure you give yourself plenty of space for the film. Answer 3: After removing the panel, […]
How do you avoid getting burn marks when shrinking fingers?
Answer 1: Some films are more susceptible to burn marks than others. Try switching up your film. Answer 2: If the fingers are especially big, try splitting them. Answer 3: Try moving from left to right faster as you heat the fingers. Answer 4: Try approaching the fingers from a number of […]
What should I do if I got the dashboard wet on a 2021 Ford F-150?
Answer 1: Park it outside in the sun, any issues with the dashboard/electronics should go away pretty soon. Answer 2: Use a soak rope and a dash towel when tinting this windshield, as it’s very easy to get wet if you’re not careful. Even a few droplets of water can cause issues. Answer […]
How do you wrap the back of a snowmobile?
Answer: Use a high-tack vinyl on the aluminum, as this is the best choice for a soft metal that will get a lot of scuffs and dents. You can also buy specialized kits for wrapping snowmobiles.
How do you tint the back window on a 1956 Chevrolet Belair?
Answer 1: Cut your pattern about a quarter-inch short before shrinking. Next, deal with the smaller fingers from the inside of the vehicle. Answer 2: You might want to call a professional to remove the glass. This is really the only way to achieve perfect results, even though there is quite a lot of room […]
Should you turn people away if they ask for illegal tint?
Answer 1: In certain states, customers can legally sue you for any traffic tickets they get if they are caught with illegal tint installed by you. That being said, filing a lawsuit is super time-consuming, and most customers don’t bother. Just know that rules and regulations differ from state to state, and you might want […]
What’s the best way to tint vehicles in lower temperatures during the winter months?
Answer 1: You really need to go overboard with your squeegee technique, making sure to push out as much water as possible. If possible, use a squeegee with a handle, as this will give you more power and control. Answer 2: You can still leave the vehicle outside to cure, you just need to […]
How do you tint a 2022 Porsche Macan?
Answer 1: Use a 50/50 approach for the front doors. Answer 2: If you’ve tinted previous iterations of the Macan, you should be all set. The only thing you need to know is that removing the horizontal trim piece is a little harder now, because the panel is much tighter. This is necessary to remove […]
What causes small white pin-head spots on windows?
Answer 1: This may be caused by contaminated water. You might also have small dust particles floating around in your shop. You could also be using a towel that is leaving behind small particles on the window. Either way, it’s always a good idea to use clean water and keep your shop as clean as […]
What is the best way to tint the back glass on a Dodge Charger?
Answer 1: Try to move with the grain of the window rather than against it. Answer 2: Use a clay bar during your prep stage. When you’re done, turn on the vehicle’s defroster before beginning your installation. The installation process itself should be fairly standard, but you might want to press a little harder […]
What are some good methods for removing adhesive?
Answer 1: Ammonia is an easy and straightforward way to remove adhesive. Answer 2: You might also want to try using a pressure washer. Answer 3: Isopropyl alcohol works well for removing adhesive. After applying the alcohol, let it sit for a brief moment before scraping the adhesive away. It should come off […]
What’s the best way to avoid breaking the glass on a 2022 Audi E-Tron GT RS?
Answer 1: The back glass is very soft on this model, so be extremely careful when tinting. Answer 2: Be very cautious if you try to pull down the 3rd brake light. This can easily lead to a mistake and a crack in the glass, especially since it is such soft glass. Tint around […]
How do you learn how to tint windows faster?
Answer 1: Double cut if possible. Double shrink for even better results. Try to speed up your scrubbing stage, as this stage can be quite time-consuming. You can also maximize efficiency by cutting down on the amount of walking you do. Make sure you’re not going back and forth when walking around the vehicle. Get […]
What causes discoloration on a 2021 Ford Expedition door handle?
Answer 1: It’s best to pull the sweep and pop those panels off before install. They can be ruined quite easily. Answer 2: If water permeates the cardboard backing behind the leather, the panels are pretty much ruined. This is caused by water going through the holes in the stitching, which causes the backing […]
How do you tint a 1989 F150?
Answer 1: Be aware that if you remove the back glass, you will need to deal with remaining hard plastic around the outside and top edges. Answer 2: Whatever you do, don’t remove the glass. If you do, you’ll need to purchase a new chrome locking strip, and these components can be hard to […]
What causes film to roll off glass?
Answer 1: This situation is becoming more and more common in the modern era with new window technology and tinting products. Basically, manufacturers are using less glue for films with higher VLT rates. Answer 2: There may be too much silicone in the dot matrix. This can cause the film’s adhesive to fail. […]
If you’re using the “double-cutting” method, should you use the passenger or driver’s side windows?
Answer 1: It doesn’t really matter which side you use, so whichever is more convenient for you. Answer 2: If you’re right-handed, it might be easier to do the driver’s side. Answer 3: Basically, you should choose whichever side presents less of an issue while trying to work around the side mirror.
How can you fix a 2021 Accord Hybrid that won’t start after tinting?
Answer 1: Unplug the battery completely and use jumper cables to start the engine. Try to keep it running until the customer picks it up if possible. With any luck, the issue will be fixed by the time the customer gets home. Answer 2: This often happens if you fail to cover the driver […]
Will tint hide scratch marks?
Answer 1: Often, the client will insist on the window being replaced if there are scratch marks. It is often difficult to hide these scratch marks with a layer of film. Answer 2: Tint can actually make scratch marks more visible under certain circumstances. Answer 3: Sometimes, the film’s adhesive layer can fill […]
What causes scratches on a Tesla Model Y sunroof?
Answer 1: These scratches can be caused by razors. Answer 2: If you use the wrong kind of scrub pad, this can also cause scratch marks. Answer 3: Scrubbing is usually an unnecessary prep task for newer cars like Teslas. A squeegee and water will usually be more than enough to clean the […]
How do you remove the rear-view mirror from a 2015 Ford F-350?
Answer 1: It is actually very easy to break the windshield when you’re removing the mirror, so you need to be very careful. Your best bet is to use a screwdriver while being as gentle as possible. Answer 2: There is actually a specialized tool that you can order that is specifically designed for […]
How do you tint a 90s-era Buick Roadmaster?
Answer 1: This station wagon isn’t as difficult as it might look. Just shrink the entire thing, make sure to tape it, and keep your tinting as clean as possible. Answer 2: You do not need to remove the rear vents. This area becomes easier if you can remove the pop to get underneath. […]
What should you do with your employees during slow months, like November and December?
Answer 1: Some tinters try to encourage their employees to file for unemployment during those slow months. Answer 2: Don’t abandon your workers during these slow months. Remember, these guys and girls are the heart of your business. Keep them around, and keep them employed. Even if they are simply sweeping up the place […]
How do you tint the windshield of a new Jeep Grand Cherokee?
Answer: The main thing you have to remember is that the dash is very close to the windshield. There is also a very wide dot matrix close to the bottom of the windshield, which is also close to the dashboard. Something else of note: there is a foam strip that is secured to the dash […]
How do you fold down the back seats on a new Toyota Camry?
Answer 1: You might have to pop the trunk and look for a handle. Pull the seat-unlock latch, and you’re good to go. Answer 2: Not all of the seats actually fold down, which would explain why you can’t find handles or buttons anywhere. Answer 3: Your best bet is to check the […]
What are the windshield tint laws in Massachusetts?
Answer 1: You are allowed a certain amount of tint if you get a doctor’s note saying that you have sensitive eyes. Answer 2: 80% tint will not pass inspection in Massachusetts. Answer 3: A full windshield tint is not allowed in Massachusetts. The top strip is legal, however, as long as you […]
What should you do if you re-install the door panels on a 2006 Honda Accord and the doors will no longer open properly?
Answer 1: The door handle wire mostly likely came off or broke. It’s a green clip that is often easy to miss. Remove the green clip and place it further back. This should make the door open correctly. Answer 2: If the green clip is broken or lost, you can hook it back up […]
What should you do if you accidentally pull the defrosters off a Ford 250?
Answer 1: If you were tasked with removing old film, you are not responsible for the defrosters. You should make this clear before you complete the job, and let the client know that you’re not liable. Answer 2: You will need to replace the glass. Answer 3: The defrosters are poorly made, and […]
How do you tint a 2022 BMW M340i?
Answer 1: Remember to use a soak shield or soak rope. Cover the dashboard to make sure you’re giving all the electrical components adequate protection. Answer 2: Try not to swipe too deep on the bottom, as the foam seal is a little higher than normal compared to previous models of the M340.
What temperature should you set your heatgun at while tinting?
Answer 1: Set it at maximum heat. The setting doesn’t matter so much, because you can control the effect by holding the heatgun away from the film at a suitable difference. Just don’t hold it too close and keep moving it around. Answer 2: 950 degrees. At this temperature, it’s possible to shrink a […]
How do you deal with window wipers when tinting?
Answer 1: Usually, you power up the vehicle, put in the keys, and activate the wipers. Then, stop the power precisely when the wipers are pointing straight up (towards the roof). This should allow you to flip the wipers up, giving you full access to the windshield. Answer 2: Just remove the wipers. It […]
Can sunroof glass explode if you tint it?
Answer 1: Many people have tinted many sunroofs with no issues reported. Answer 2: Interestingly enough, sunroofs can explode whether they have been tinted or not. Therefore, if a sunroof explodes it may not be due to the window film, but rather the inherent qualities of the sunroof glass. Answer 3: Some tinters […]
How Do You Tint a Salem CruiseLite Trailer/Mobile Home?
Answer 1: You can use regular film on these trailers. The biggest issue is dealing with the seals, but you can tuck your film in the same way that you would tint most automobiles. Some of the windows on this trailer are actually comprised of two separate pieces of glass, so keep that in mind. […]
Do Freezing Temperatures Affect the Tinting Process?
Answer 1: Use warm water instead of hot water, as this will stop your hands from freezing. Answer 2: If you live in a state with a very cold climate during the winter, the residual application solution can actually freeze overnight. This is usually an issue if temperatures dip below 25 degrees during the […]
Can You Get Pulled Over for Tinting Your Window in Illinois?
Answer 1: You can get pulled over for having 20% tint on your windshield in Illinois. However, this is pretty rare, and some people drive their entire lives with 35% tint without ever getting pulled over. Answer 2: If you have 5% around your entire vehicle, you’ll likely never get pulled over in Illinois. […]
Which is Better, a Stationary Peel Board or a Mobile Peel Board?
Answer 1: Mobile peel boards are great, but only if you have enough space. You need plenty of space to move mobile boards around, and if your shop is too small, there’s really no point. Answer 2: Mobile peel boards are good because you can reduce the distance between the window and the work […]
Should I pay car dealerships to refer their customers to my window tinting business?
Answer 1: Many tinting shops do this, as it attracts new business on a consistent basis. Answer 2: You might also consider referring people back to the dealership as payment instead of actually paying a fee. Answer 3: You can also get dealerships to charge their customers beforehand for your services. That way, […]
How do you tint the back door windows on a 2022 Range Rover?
Answer 1: Remove the bottom load gaskets, as this will make the job much easier. Answer 2: Take out the bottom seal before you tint, and you’ll find that life is much easier. Answer 3: New Range Rovers have windows that feature a hydrophobic coating. This repels water. Basically, you’ll need to use […]
After a new windshield is installed, do you need to wait for the glass to cure before tinting it?
Answer 1: You might want to wait 3-5 days before tinting. It’s better to err on the side of caution, as you want a good seal before you start tinting. Answer 2: Generally speaking, you can tint windows the day after they’re installed. Answer 3: If you tint a window on the same […]
How do you tint the back glass on a 2011 Mustang convertible?
Answer 1: It’s very difficult to slide the film behind the seal on these models. This means that you will not have enough space to slide it behind, and you will mostly need to use guesswork to come up with a good final result. Answer 2: Hang a quarter of an inch over the […]
What size film should I carry if I’m running a mobile tint business?
Answer 1: The majority of your film should be in 36” rolls. You can carry a little bit of 24” film for privacy glass, and you might also want to carry one or two rolls of 40” film for a minivan or a similar vehicle. Answer 2: Just carry 60” rolls, as you will […]
How to tint a 1987 Toyota 4-Runner?
Answer 1: Remove the hardware first. Answer 2: You need to really go the extra mile with your cleaning stage before you tint and lay your film down. Try to make your cuts as clean as possible, because it is easy to waste film with this particular car. Answer 3: Many tinters turn […]
How to remove water marks on a Chevy Silverado after three months?
Answer 1: You can avoid this scenario by tinting properly in the first place. Remove the screw to pop out the top of the panel, shift it back, and remove the sweeps. Next, cover the door panels with liners before tinting. Use a tri-edge squeegee to push the liner near the panel towards the bottom […]
How do you tint the corners on a Dodge Challenger front windshield?
Answer 1: You should leave it longer before pulling. Answer 2: Go outside the line first, then shink to the side while going in the “wrong direction.” This will will create a crease, but the key is to do this all the way to the edge. Answer 3: Try trimming it smaller than […]
What do you put underneath the film to make it move smoothly?
Answer 1: Baby powder Answer 2: Dryer sheet Answer 3: Liquid fabric softener Answer 4: When you see videos with film moving very smoothly during the application process, the tinter is usually using very high-quality film. High-quality film moves much more smoothly. You should also look for film that shrinks well. […]
How do you tint a BMW M6 convertible rear window?
Answer 1: Use a sharpie for the bottom. Cut an oversized pattern on a peel board. Dropping the roof may make it easier to tint the rear window. Line up your bottom edge with the dot matrix. Pull the sweeps and use an Allen key to manually get that rear window as high as possible. […]
What’s the best way to tint a 2013 Dodge Dart windshield?
Answer: All Dodge windshields tend to cause tinters trouble. Your best bet is to remove all the pillars. Then, fill the pillar holes with rags or towels. Definitely use a soak rope or a dash towel when tinting the windshields. Your main concern is getting the electronics wet. Dodges seem to suffer from this […]
What’s the best way to cut an RV window with a non-removable screen?
Answer: Line up the factory straight edge of the film with the side of the window that lies behind the screen. Next, trim the top and bottom and remove the film. Once the pattern is removed, flip over the film and line it up with the factory edge. Next, cut the bottom edge of the […]
How do you tint the back glass on a 2008 VW GTI?
Answer 1: Pull the trim on the back glass for a much easier install. Answer 2: Use the soap shrink method with a low anchor. Start just a few inches above the wiper, and make sure that your anchor sits above the heavily curved bottom corners. Don’t worry about using any side anchors, just […]
What should you do if you get the side pillar on a Tesla wet?
Answer 1: If you leave the vehicle in the sun, the side pillar should dry out relatively quickly. The sun should also clear up any discoloration. Answer 2: Whatever you do, don’t try to use a heat gun to dry out the pillar. Answer 3: Use a dry towel and wipe the pillar […]
What should you do if your shoulder injuries are preventing you from working?
Answer 1: Chronic houlder injuries are quite common in the window tinting industry, especially if you’ve been doing it for multiple decades. The best thing you can do is hire people and step back to take more of a management position. Answer 2: Cut down the number of cars you tint per day. It […]
How do you remove the headrest on a 2021 Ford Ranger?
Answer 1: Instead of removing the headrest, simply flip the seat bottom-up. This will provide you with enough room to tint inside of the cab. Answer 2: On the left side of the headrest, you should be able to find a small locking button. You’ll need to access this button with a small flat […]
My plotter isn’t cutting correctly. How do I calibrate it so that it cuts correctly? It is either cutting too deep or not deep enough.
Answer 1: Try a 25 or 30-degree blade. Answer 2: You need different blades for different films. Use a 45-degree blade for ceramic and a 30-degree film for standard films. You can actually save your calibrations for each film type, allowing you to easily switch the blade settings based on whichever type of film […]
Are the rumors true? Does tinting Tesla sunroofs with 5% tint really crack the glass?
Answer 1: The main issue is actually absorption. Anything darker than 70% will increase the absorption rate considerably. This means that whenever the vehicle is moving, cool air will deal with the absorption. But as soon as the vehicle comes to a stop for an extended period of time, the glass will become incredibly hot. […]
Is bottom-leading the best tinting technique?
Answer 1: Bottom-loading is the most efficient tinting technique as it will allow you to tint more cars during each working day. Answer 2: Bottom loading creates a much cleaner finished product because it elevates the side creases. Answer 3: Bottom loading is almost always the best option, except for vehicles that have […]
What’s the best tool to remove maximum soapy water from the bottom of a back window if both bulldozer and titans aren’t working?
Answer 1: Use a side swiper style squeegee. Answer 2: The reach. Answer 3: Stroke doctor. Answer 4: Tail fin.
How do you avoid scratches on Tesla windshields?
Answer 1: Newer glass is much easier to scratch. While you might have been able to get away with cutting on the glass in the past, this is no longer viable. Use a sharpie to create the pattern before transferring to a peel board. Cut the pattern there. Answer 2: Use glass aid. […]
How do you remove excessive amounts of coating (like Armor All) from a panel?
Answer: Evenly wipe the panel then dry it. Use a heat gun to make the process faster. This will allow you to stick things to the panel.
How do you tint the split window on a Chevy ‘63?
Answer 1: You should try pulling the windows, as this is much easier. Answer 2: If you try tinting these windows without pulling them, your main challenge will be getting inside the car. The space is quite tight. Answer 3: Be wary of the outer edge and the inner edge on the gasket. […]
What should you do during “slow season” as a window tinter?
Answer 1: Focus on SEO and website tasks. Make sure you get plenty of good reviews on Google. Maybe look into online advertising options. Answer 2: Take the opportunity to spend time with family, go on vacation, and enjoy some time off. Answer 3: Switch to other services. Some ideas include detailing, chip […]
How long does it take for window tint to fully cure?
Answer 1: About 24 hours on a normal sunny day. Answer 2: To be on the safe side, you should give your customers an estimate of 48 hours. You might also want to instruct them not to roll down the windows for 48 hours. Answer 3: The curing time depends heavily on your […]
How do you use the marker method and make sure that the film lines up?
Answer 1: Line up the bottom first. Next, cut the sides halfway up the window. Finally, roll the window down two inches and finish the rest of the cutting. Answer 2: As you cut, try to maintain the correct angle and curve towards the marker line. Answer 3: Place the straight bottom edge […]
What is the best way to deal with wind as a mobile tinter?
Answer 1: Get a pop-up tent. However, it’s very important that you properly secure your tent. Otherwise, the tent may come loose and strike the side of your client’s car. Answer 2: Read the weather forecast and schedule your appointments around that. Answer 3: Work inside your client’s garage.
What’s the best way to display your shades so that the customer can choose the best option?
Answer: You can acquire a wall display from the manufacturer of the film in many cases. Otherwise, you can purchase a piece of plexiglass and create your own display, showing the various effects that different types of film have on normal glass.
What should you use as a layer between the film and glass when you shrink?
Answer 1: Dryer sheets. Answer 2: Baby powder. Answer 3: Put some liquid dish soap on a paper towel, and then spray the paper towel with water. Next, run it on the windshield and let it dry. Answer 4: Using a layer between the film and glass might not even be necessary […]
What’s the best way to clean a window before tinting?
Answer 1: Tape your seals completely before cleaning. This helps you avoid contamination. Answer 2: For the back window, you might want to avoid using a blade. Instead, use scrub pads and squeegee spray. Answer 3: The first step is always to make sure that you’re working in an area without dust. If […]
How do you deal with contamination?
Answer 1: In many cases, the source of contamination is actually your floor. Sweep the area and hose it down if necessary. You may also need to do this to your peel board. Basically, you need to wet down anything within five feet of the film, including the car door frame. Answer 2: Isolate […]
How do you tint a 1977 Datsun?
Answer: Watch out for the quarter windows, as they have a chrome trim that can be problematic. The windows also have a small amount of bow. Watch out for the front doors as well, since there is very little space by the mirror after you roll the window down even a little. Unlike many other […]
How do you get rid of static when using carbon films?
Answer 1: Lightly mist a dryer sheet and use this to wipe the entire window before install. Remember to let it dry before laying down your film. Combined with the dry shrink technique, this should help you avoid issues with static. Answer 2: Dust some talcum powder over the dry screen and then create […]
Is there a “special trick” to tinting curved back glass on older model Corvettes?
Answer 1: First, take the shocks and latch buttons off the window. You need to shrink these windows, and be prepared for much bigger fingers than a normal window of this size. The key is to take your time. Use an oversized piece of film. Alternatively, you can use buttonholes, but make sure that these […]
How do you block the tamper on a Toyota Yaris GR so that the window doesn’t automatically go up when you close the door?
Answer 1: One method is to use a harbor freight. In order to stop the film from peeling when the window goes back up, you may also want to heat seal the edges. Answer 2: A simple clamp should do the trick. Maybe use a towel as well. Answer 3: You can simply […]
How do you avoid issues with Tesla windows automatically going up and down after tricking the door latch?
Answer: Get inside the car, close the door, and roll the window all the way down. Then, hold down the window button for five seconds. Next, roll the window all the way back up, and hold the button once again for five seconds. This should reset the window mechanism. You may have to do this […]
How do you stop bubbles from forming on tinted rear lights?
Answer 1: Try not to force or stretch the tint film too much. Start applying film in the recesses first. That way, you won’t have to stretch the film as much when you move to the flatter areas. Answer 2: You may want to use two separate pieces when wrapping rear lights, especially if […]
How should you go about tinting a tractor?
Answer 1: Charge considerably more for these vehicles than you would a normal car. They are incredibly time-consuming and frustrating to tint. Answer 2: Remove all of the glass before installation. It is well worth the extra time and effort and will actually save you time in the long run. You will also likely […]
How do you tint a BMW x6?
Answer: The back screen is a long way from the ground, which means you may have trouble reaching the back screen. Take care when you take off the cover, as the rear stop light can be clipped and broken. Slide-out the pegs to unlock the light case.
What should you use to protect doors from getting wet?
Answer 1: Get some indoor faux leather upholstery and cut it down to the right size for average car doors. Then use this to cover the door prior to install. Answer 2: Carpet Shield works quite well. Answer 3: Use the liner from your window film, especially from big pieces of film. Then […]
What should you do if a customer complains about a squeaking window after a tint job?
Answer 1: Direct the customer to the dealer and inform them that they will need to address this issue via their manufacturer warranty. Answer 2: The door window mechanism may need to be lubricated.
How do you avoid burning the edges of the doors and windows when you using a torch?
Answer 1: Keep the torch far away from the surface and move it quickly across areas. This will ensure that the edges are adequately heated without burning them. Answer 2: Never use a torch on the windshield, as you can break the glass under certain circumstances. Answer 3: You might want to avoid […]
How do you get rid of the “Keyless Start System Problem” error message on a 2021 Honda Civic Type-R?
Answer 1: Use soak shield rope before installation. Answer 2: If the battery died, that may be the issue. Answer 3: This is caused by getting some of the electric components wet. Put a fan inside the vehicle and let it dry for 24 hours. Answer 4: Although this error message appears […]
What is the best squeegee for rear windows?
Answer 1: Blue Max or Orange Crush will successfully remove most of the water when dealing with rear windows. Answer 2: True Red Turbo is a good option for red windows.
How should you go about tinting a tractor?
Answer 1: Charge considerably more for these vehicles than you would a normal car. They are incredibly time-consuming and frustrating to tint. Answer 2: Remove all of the glass before installation. It is well worth the extra time and effort and will actually save you time in the long run. You will also likely […]
What should you do if the lamination is failing on windows?
Answer 1: Replace the glass. Lamination failure between the panes cannot be addressed any other way. Answer 2: The lamination may be failing slowly. If this is the case, it may be safe to tint the surface, but understand that the lamination will eventually fail completely and the window will need to be replaced. Answer […]
What should you use to protect doors from getting wet?
Answer 1: Get some indoor faux leather upholstery and cut it down to the right size for average car doors. Then use this to cover the door prior to install. Answer 2: Carpet Shield works quite well. Answer 3: Use the liner from your window film, especially from big pieces of film. Then […]
What should you do if a customer complains about a squeaking window after a tint job?
Answer 1: Direct the customer to the dealer and inform them that they will need to address this issue via their manufacturer warranty. Answer 2: The door window mechanism may need to be lubricated.
How do you avoid burning the edges of the doors and windows when you using a torch?
Answer 1: Keep the torch far away from the surface and move it quickly across areas. This will ensure that the edges are adequately heated without burning them. Answer 2: Never use a torch on the windshield, as you can break the glass under certain circumstances. Answer 3: You might want to avoid […]
How do you get rid of the “Keyless Start System Problem” error message on a 2021 Honda Civic Type-R?
Answer 1: Use soak shield rope before installation. Answer 2: If the battery died, that may be the issue. Answer 3: This is caused by getting some of the electric components wet. Put a fan inside the vehicle and let it dry for 24 hours. Answer 4: Although this error message appears […]
What is the best squeegee for rear windows?
Answer 1: Blue Max or Orange Crush will successfully remove most of the water when dealing with rear windows. Answer 2: True Red Turbo is a good option for red windows.
What’s the best way to safely and effectively tint residential or commercial windows that are extremely high off the ground?
Answer 1: Scaffolding is the safest option. It is also relatively cheap. Answer 2: Another option is to use a Skyscraper ladder. However, many tinters believe that there are safety concerns associated with using a ladder. Answer 3: If you have the funds, then a scissor lift might be the best option. This […]
How do you tint a 1966 Mustang Fastback?
Answer 1: You may want to pull the back glass. This will help you avoid contamination or gaps. You may also need two to three people to help you with this window. Two people can stretch the film, while a third individual can focus on shrinking. Answer 2: Trim the inside of the gasket […]
Why are bubbles so common on the back glass and passenger doors of Ford Fusions?
Answer 1: These bubbles are extremely common, even with high-quality film. That being said, low-quality film fails more often. It’s best to use the best film you have, as the film will be subjected to considerable stress as you try to tint the window. Answer 2: It is a notoriously difficult window to tint, […]
How do you avoid fingers on the quarter windows of a 2001 Nissan Sentra?
Answer 1: There is a technique known as the double-snap shrink that works well with these windows. This involves lifting the bottom up four inches after your initial shrink before shrinking once again. Answer 2: Fingers are often caused by inadequate prep work, especially if you’re working with a dirty vehicle. Answer: Use […]
How do I get rid of tiny bubbles around the frost lines?
Answer 1: You can avoid this by simply using tack cloth as your final step when you prep the window. Answer 2: This may be happening because you’re letting the film touch the head liner during installation. You can avoid this by taping the head liner with painter’s tape. Answer 3: This can […]
How do you get rid of small dots that look like water droplets after a tint install?
Answer 1: Let it dry fully, and the issue will probably resolve itself. Answer 2: The issue may have been the squeegeeing technique. Remember to squeegee hard and try your best to get rid of air bubbles. Answer 3: These are most likely globs of solution. Rinse and scrub all of your equipment, […]
How do you tint a rear window on a 2015 Honda Accord?
Answer 1: These windows should be easy if you use a general H-pattern technique combined with a heat-push approach. Answer 2: The rear window is actually easier than the doors, which can be challenging to shrink even with a bottom-loading technique. This is largely due to the extensive curvature of the roll downs.
How to tint the back window on an older Mercedes 190F?
Answer: The only thing you really need to keep in mind is that the plastic/trim on these older vehicles is actually quite fragile. Exercise caution when tinting to avoid breaking it. This is especially true for the third brake light tabs and the deck lid.
How should you approach the window keypad on a 2021 Tacoma?
Answer: This is actually a working product that provides the user with entry if they ever get locked out. Because of this, you need to be very careful when tinting around the keypad. The best option is to simply cut around it, as you should not attempt to remove it as you would a sticker. […]
How do you tint the back window on a Dodge Neon?
Answer: Use a dry-shrinking technique. If this window is giving you trouble, you may need to move your center tack line down before you begin shrinking.
How do you shrink ceramic film onto the back glass of a 2000 Chevy Cavalier?
Answer 1: Pull all fingers up towards the top when you shrink your film. This film will only shrink upwards and downwards, and not to the sides. Answer 2: Another option is to make a relief cut and then roll the film onto the glass. This is a slightly older technique, but it works […]
How do you tint the back window on a soft-top convertible with a vinyl back window?
Answer: Generally speaking, you can never tint vinyl. Instead, focus on tinting the side windows. You can use a luxe finish or spray on the vinyl that will provide similar results.
How do you tint a curved glass roof on a boat?
Answer 1: Avoid using any heat whatsoever. Leave the film long and make sure to trim on the “on” side. Answer 2: Wet shrink the film. Push fingers past the curve, and lay the film on the surface in an angled position.
How do you tint the back window of a 1992 GT-S Skyline?
Answer 1: Regularly check the glass while you tint to make sure it’s not getting too hot. Use the split fingers techniques, leave the film long, and pull carefully and slowly. Answer 2: Use an “H-pattern” technique. Make sure that you’re regularly distributing the heat from side to side with your heat gun.
How do you remove tint by the third brake light on a 2014 Passat?
Answer: Pull the deck to make this job easier. You should also use a steamer to help you remove the tint. Let your client know beforehand that this job will be more time-consuming, and therefore more expensive.
How should you tint around the window louvers on a car such as the Chevy Camaro?
Answer 1: The louvers themselves are partly designed to reduce glare and reduce cabin temperatures, so tinting the back window may not even be necessary. Answer 2: Simply remove the louvers and tint as normal. They can be removed relatively easily. Answer 3: You can use a plotter to tint this surface without […]
What’s the best way to remove dried baby shampoo and water from the back of a 2021 Honda Accord?
Answer 1: Spray isopropyl alcohol in the hard-to-reach spots, then follow up with a scrubber. Next, spray down once again with alcohol and finish by letting the entire area air dry. It should be clean. Answer 2: You can try stapling velcro to a paint stick or ruler and use it to scrub the shampoo […]
Do I Need a Backup Plotter?
Yes, it’s probably a good idea to have a backup plotter available if your operation is highly dependent on plotters. Even the most dependable plotters can experience issues, and a backup ensures that you can still continue serving customers while you get your main plotter repaired.
How to tint a 2021 Nissan Rogue
Method 1: The main difficulty with these cars is the tightness of the seals. If you plan on hand cutting to the gasket, you will have just enough film to slip underneath by about a millimeter. Under the gasket is a layer of black vinyl that may have to be removed if the film isn’t […]
How to tint a 1997 Ford Thunderbird
Method 1: Do very little shrinking on the bottom of the back glass. When installing, anchor the bottom portion of the back glass on the center of the film, and reverse squeegee from the corners inward to the center. It can be helpful if someone holds a heat gun over top to keep it down. […]
How to tint the front doors on a 2019 Chevy Colorado
Method 1: Hand-cutting these models can be a little challenging but makes installation easier. If using a plotter, be generous with your slip solution, and remove the panels completely. To remove the panels, find the 7mm bolt behind the handle and unscrew it. Push on them from the top the same way you would do […]
How to fix a lit up airbag light on a 2018 Porsche Cayman S
Method 1: If the airbag light came on after tinting, then it’s likely because it became wet from the slip solution during the process. The other likely reason is that you were sitting on the front edge of the seat, and the pressure tripped the sensor, igniting the airbag light, but not actually deploying the […]
How to tint a 2020 Porsche Turbo
Method 1: Use a scrub pad to clean off all the windows. Oftentimes, plotters won’t have cutouts for the rear wiper so be prepared to trim that out if need be. Never take a blade directly to the glass of the rear window. There is a coating on it that will scratch if it comes […]
How to prevent tint from scratching when rolling the windows on a 2018 Porsche Panorama
Method 1: Trim off the inner rubber and replace it with 2 inches felt. Method 2: Remove the door cards completely. Then use adhesive promoter to clean the plastic weatherstrip. Next, install a 3/8th inch strip of black moleskin. Tint the car as normal, and then reassemble everything in reverse order. Consider charging above $1,000 […]
How to tint a 2021 Porsche Taycan
Method 1: The back and rear quarter windows are easy enough for any sophomore tinter to handle. The sides are a type of suede and need to be taped off. If a customer wants the tint to be wrapped around the brake light, consider removing the brake light to make it easier to install. It […]
How to fix plotters that are making odd mistakes and anomalies
Method 1: If your plotter is making odd mistakes on patterns, there are a number of solutions you can try. For example, you might be seeing rounded corners on squares or little slivers of film splitting off on edges. First, double-check that you don’t have any grip wheels that may be worn out or in […]
How to use a plotter to optimize volume and efficiency in a tint business
Method 1: One of the best ways to optimize time, and therefore money in a tinting business is to have film pre cut before cars arrive. Determine which cars come in the most and have 5-10 pieces of film already waiting to be installed beforehand. Cut the pieces you need when you have time and […]
How to get a clean cut with crystalline tint using a plotter
Method 1: First of all, consider whether or not you really need to use crystalline. It is inherently more difficult to get a clean cut with this tint because of its material composition. Method 2: Make sure the plotter’s blade is still up to par. If white residue gathers up on the blade when it […]
How to choose the right sized plotter
Method 1: If you are only doing cars, you can almost definitely get away with exclusively using a 40-inch plotter every day. For a little bit extra, a 42 inch can also suffice if you anticipate needing it. There are only occasional times that a 60-inch plotter is necessary. For example, the sunroof on some […]
How to secure a plotter to the inside of your trailer for mobile tinters
Method 1: Bolt it to the floor of the trailer using rubber or felt feet on the bottom. Depending on the trailer, you may need more or less material on the bottom to dampen any vibration. You can also consider putting a thick layer of carpet on the entire bottom of the trailer so you […]
How to optimize the visibility of your plotter cut lines on peel boards
Method 1: Use an L.E.D flashlight to light up the cut. Usually it will turn the line bright white. Method 2: Spray foaming window cleaner can also increase the visibility of the cut lines. Method 3: Set up a vertical cutting station on a peel board rather than cutting horizontally, and having lights set up […]
How to remove factory adhesive on a Lexus NX 300
Method 1: You can try a good adhesive remover like ATR to remove adhesive from these models, but some tinters swear that a simple steamer is just as effective. To use a steamer, direct the steamer at the glass and get a feel for how much heat and moisture it needs before the adhesive comes […]
How to remove the door panel on a 2018 Volvo V-90
Method 1: Remove the window switch with a pick or pry tool, then remove the T-20 screw from behind the switch. Next, remove the T-20 screw from under the armrest. Pry the trim piece from the center to the front (not from the rear, as this can break it). After the trim is popped from […]
Why did the glass burst on a Volvo SUV passenger door after tinting?
Method 1: There is no reason this should happen, even in extreme temperatures, unless there was a sudden drastic change in temperature. For example, a running car in a heated garage or shop can sometimes have glass breakage if it suddenly speeds out into freezing temperatures, but even that is rare. The most likely culprit […]
Why do my Mazda 3s keep getting bubbles in the rear window?
Method 1: These models are known for strange flaws happening on the rear window, regardless of the level of experience of the tinter. These anomalies only seem to happen on the Mazda 3, but not the other Mazdas. One theory posits that there is a design flaw that allows moisture to build up inside the […]
How to remove the sweeps on a 2019 Mazda 6
Method 1: Pop the clip just behind the speaker – either with your hands or a small pry bar. Then pry back on the top outer edge with your hand and pull out the sweep. Method 2: Stick a bone tool inside and push them out, or unscrew the door handle and pop them out. […]
How to tint passenger doors on the Mercedes s550 with factory light gaps at the top
Method 1: There is nothing you really can do besides line up the tint with the top of the glass or line it up with the top of the tint. The customer should be briefed on the situation so they’re not confused as to why the gap is still there when the job is done. […]
How to install film on a rear side passenger door window on a Mercedes 300
Method 1: Taking them out and reinstalling them isn’t actually necessary 100% of the time. Instead, you can save time by shrinking it and tripping the door up before bottom loading it. If you’re not comfortable yet with bottom loading, then you can try doing a two-stage install. The seals aren’t that tight on these […]
How to fix problems with Harmon Kardon sound system on an Audi 2 Series after tinting
Method 1: It’s important to act quickly and disconnect the system. Put it on a flat dry surface and try to dry it out. It can be accessed by removing the covering in the rear trunk and simply removing the screws that hold it in place. The entire removal process can take about 20-25 minutes, […]
How to tint the windshield of a 2016 Range Rover
Method 1: Because of the tight sides, a bulldozer often won’t fit inside. If you do manage to get a bulldozer inside, be careful not to rip the film out when you remove the bulldozer. Use less water and slip solution. Consider asking for help from a second person to install it so it’s easier […]
How to prevent dashboards from reflecting in the windshield
Method 1: Don’t use metalized film on front windows Method 2: Apply lighter film that blocks equal or more light. Method 3: Sell or recommend a dash mat to the client to prevent reflectiveness on the dashboard.
How to fix one light not turning off on a Honda Civic Type R after tinting
Method 1: There is a module on the bottom of the windshield on the right that is extremely sensitive to water. Even when using a dash cover and soak rope, these modules can leech moisture and cause electrical problems. These cost over $1000 to replace, so hopefully if you’re experiencing electrical problems, a simple dry-out […]
How to get rid of haziness on the outer edges of a 2020 Honda Civic hatchback
Method 1: Try using a sideswiper instead of a bulldozer. Method 2: Simply give it time to cure and settle. Haziness can simply be the result of extra moisture, which will dry out. It could also just be glue smear, which will fade away over time. Giving the window time to fix itself is more […]
How to remove panels on Honda/Acuras without breaking the door latch securing piece
Method 1: The first option is to simply not remove door panels, as these can be very challenging not to break. Method 2: Try fixing them afterward using hot glue, or by clipping them together. You can also epoxy the two pieces back together. Method 3: Buy new pieces and charge accordingly while explaining the […]
2019 Ford Raptor has a crack in the windshield immediately after tinting. What happened?
Method 1: Windshields on Ford Raptors are not known to break after tinting, so it’s possible there was an issue with the removal of the mirror. Fords are notorious for difficult rearview mirror removal. Tinters inexperienced in removing them may not realize how touchy they are, and put stress on the glass which then later […]
Why did the deck on a 2019 Ford Fusion turn into powder as soon as I touched it?
Method 1: This has nothing to do with your solution or any other tinting-related issues. It’s simply a flaw from the manufacturers that is common in a lot of Fusion models. This problem should be taken up with the dealership. Tinters working on used Fusion models need to make a note of this and either […]
Why does my 2020 Audi A4 have a random vertical scratch on the door window?
Method 1: This is an occasional flaw that happens due to the dealership. There is a small clip that can get bent inside the door that will scratch the glass when the window gets rolled up and down. Any client with this issue should be sent to the dealership.
How to fix the disabled lane-assist on a 2015 Audi S3
Method 1: If this happened after tinting, the likely culprit is an evaporated drop of tint solution blocking the sensor. To fix this, carefully remove the camera and the pyramid before cleaning off the residue. The camera should recalibrate itself after you drive it around for a few minutes. To avoid this in the future, […]
How to protect a 2014 Audi S5 when tinting the windshield
Method 1: You can try using a soakrope if you have one small enough, but the tight space is the main problem most tinters have. Method 2: Instead of using a soakrope, take your dash cloth cover and put that inside the crease. Then take a shammy and put that down as well to soak […]
How to tint a 1969 Ford F-100 windshield
Method 1: Just like with a lot of older trucks, you’ll want to rough cut the bottom and slide the film down so it’s overlapping the bottom by an inch or so. Then you can rough cut the top as well, overlap it by an inch or so again, then shrink it. Repeat the process […]
How to tint a 1995 Ford Mustang
Method 1: Wet sand the matrix with 1600 grit sandpaper and make sure to really clean thoroughly with the solution of your choice. The invisible stick glue method tends to work very well on these models if you’re comfortable with that technique. The key is to remove the clearcoat from the dot matrix in order […]
How to prep the defrosters on a 2021 Dodge Challenger
Method 1: If you’ve done all the prep work in the world and you’re still getting peanuts and bubbles along the defroster lines on this model, you could consider using a different type of film. Some films react better with some defrosters than others. The most common prep work strategy is to use a clay […]
Why are defrosters peeling off my 2020 Ford Explorer?
Method 1: These defrosters are notorious for peeling off for no apparent reason. In the last few years, Ford’s glass manufacturers have switched up the manufacturing process. This has led to many models with faulty defroster lines. It could also be a mistake at the end of the manufacturing process where they forget to peel […]
Is the 2021 Ford F150’s computer cut the same as the 2020 model?
Method 1: They have slightly different designs, but you may be able to approach both with the same general method. The newer model may require some extra shrinking and trimming. If the truck has sunroofs, then these have to be taken into account as they are 100% different between the 2020 and 2021 models.
How to tint rear quarter windows on a 2019 Ford Flex rear quarter windows
Method 1: The 2019 Ford Flex has a known problem with the laminated glass cracking easily. According to Ford, it usually happens after the vehicle goes over a bump in the road at high speeds. Some tinters will refuse to tint these because of how fragile the glass is and how easy it is to […]
How to take care of fingertips that are cracking from heavy window tinting work
Method 1: The constant pressing of window film can eventually rub your fingertips raw and cause the skin to crack. Once it’s cracked, it gets stuck in a vicious cycle of healing a bit, then cracking open again and being worse than before. The key is to give the fingertips as much moisture as possible. […]
How to get rid of fingers on the edges of the 2020 Subaru Legacy
Method 1: Fingers usually happen when the liner shrinks more than the film. Leave your strip of film there and weed it after it’s already been shrunk. This will ensure that everything gets shrunk at the exact same rate.
How to tint around the sensors of a 2021 Toyota Highlander
Method 1: Try tinting the entire thing into three pieces: One for the middle, and one for each side. Prepare the dot matrix by sanding it down with 400 grit sandpaper. This will allow the matrix to stick to the film properly. Then clean off the debris thoroughly. Install each piece of film starting from […]
How to tint the back glass of a 1991 Honda Civic with ceramic film
Method 1: The main challenge with these backglasses is having the corners scrunch up. To avoid this, cut the film longer in the corner sections. Use one hand to pull the edge away from the vehicle and then shrink starting from the corners, moving inwards to the middle. You can also make relief cuts on […]
How to tint a 2021 Kia K5
Method 1: A tinter may charge the same amount as a Volkswagen or an Audi on these cars based on the tightness of the doors. The side gaskets are really deep, and the glass contains a strong emulsion which makes it very sticky. There are no screws needed to pull the sweeps, as you […]
How to avoid specks on tint jobs.
Method 1: There is an endless amount of little things you can do to avoid particles landing on the glass before the film goes over the top. Mobile peel boards help minimize specks because you always have a clean, flat, easy surface to peel from. This minimizes the chance of the film coming into contact […]
What causes scum/soap coagulation?
Method 1: Sometimes dried soap suds will build up over time. Your filters need to be cleaned and rinsed with hot water as often as you can to prevent the build-up of gunk. Some soaps are more prone to this happening than others, and there is some debate about which ones are best. Many tinters […]
How to tint the taillights on a 2017 Ford Focus Hatchback
Method 1: Using the “pre-stretch” technique, stretch out your film beforehand, and then use memory form to shrink it back to fit the light. This technique helps to minimize bubbles or peanuts. You can also lay the bottom half first and make sure to leave no fingers whatsoever. Finally, you can gently pull upwards while […]
Why is the bottom of the window peeling after rolling up the windows?
Method 1: If you’ve just tinted a window, and now the bottom edge of the film is peeling off after rolling the window up and down, you most likely didn’t slip the film deep enough into the seal. This means that when the window is rolled down, the edge of the film is catching the […]
How to tint the front passenger doors on the Nissan Rogue 2021
Method 1: These doors can be tinted relatively easier than most except for the little piece of rubber in the bottom corner (next to the mirror). Nissan claims to have put them there to stop the glass from rattling. However, they are commonly removed for tint jobs anyway in order to get the film to […]
Why are there bubbles in the dot matrix of my 2007 BMW 328?
Method 1: If you’ve tinted the back glass of a 2007 BMW 328 and there are bubbles or streaks in the dot matrix, it’s because the matrix wasn’t prepared enough before installation. This means that it won’t completely adhere to the film. Some dot matrixes can be roughened up with a razor blade, but use […]
How to remove the rearview mirrors on a 2021 Ford F-150
Method 1: Notoriously “sketchy,” Ford rearview mirrors have a certain system for removal. Before you do it, consider whether or not it’s worth breaking the glass in order to put a piece of tint on it. It’s okay to either turn the vehicle away or ask the customer to take it to a glass shop […]
How to prevent glue breakage on backglass tint jobs
Method 1: Some film utilizes CDA technology where the adhesive is activated when physical pressure is being exerted. This means that any streaks from glue breakage might mean that you’re pressing too hard with your fingertips when shrinking or installing. If you have already significantly increased the amount of slip solution you use then this […]
How to tint past the weatherstrip on a 2021 Ford 150
Method 1: These weatherstrips are incredibly tight, so if you have trouble, you can remove the entire panel instead. Remove the five screws and pop the panel off. Then remove the sweep. This will give you access to where you need the tint film needs to go. After the sweeps are pulled, apply the film, […]
How to prevent bright flashing lights, such as at a nightclub, from shining through the windows to the outside
Method 1: Try using a tint meter to know how much light needs to be filtered out. If the glass is dual-pane or Low E glass, it’s best not to go any darker than 25% if it gets direct sunlight, especially in hot climates. It will almost definitely overheat and crack and/or shatter eventually. If […]
Why is my door panel fabric stained after tinting?
Method 1: Certain types of dish soap or baby shampoo can eat away at the dye of leather or fake leather on door panels. Additionally, oven cleaner can also leave marks and destroy door panels. Generally speaking, abrasive substances like dish soap or oven cleaners should be avoided, and panels should all be covered or […]
Tinting around the sensor in the Mercedes s550 windshield
Method 1: This is still a matter of debate. Some say that you should never try to mess with any sensors on a car, while others figure that if a sensor can work with rain, dirt, fog, and other issues, it’s not going to have any problems. When in doubt, either cut around the sensor […]
How to tint side doors on a 2021 Mercedes AMG GT43
Method 1: Unfortunately the sweeps on this model will scratch the tint when you roll the windows up and down. If you want to avoid having to replace all four doors, explain the situation to the client and offer to replace the gaskets with fuzzier ones. A general rule of thumb for determining whether or […]
How to tint the back glass on an Escalade ESV
Method 1: These models are similar to tinting a Chevy Avalanche. It’s best just to pull the glass, hand cut it, and then replace it while hiding the slits under the metal bands. There are little clips that allow you to pop the glass. Some tinters will use black caulk around the edges as well. […]
How to tint the quarter windows on the 2014 Mazda 3 four-door.
Method 1: Use the pointy, pizza slice-shaped cards to place the film. The gaskets are very tight, and might not be worth it to try and remove. These windows have to be hand cut in place and slipped under the gasket by stretching them out with a pry tool. When shrinking, use little to no […]
How to remove the sweeps on a 2020 Mazda 6
Method 1: You will find wide sweeps in the upper channel. Pop the clip behind the speaker so you can loosen the panel a little bit, and then use a bone tool or pry bar to pry out the top outside edge with your hand until you can fit your hand in to grab the […]
A 2018 Subaru Forrester won’t start after tinting it, what happened?
Method 1: It could be that the battery is exhausted. If it’s a brand new vehicle, it could have sat at the dealership draining power for weeks if people were neglecting it there. Try recharging the battery and restarting it. If it won’t start after the battery has been charged, then you can probably rule […]
How to tint around the smart camera in a 2019 Subaru Ascent
Method 1: You can usually get away with tinting right over top of it without affecting the camera. However, many tinters would prefer not to mess with warranties or the effectiveness of the camera. Unless the customer is totally adamant on having an entire sun strip across the back glass, it is probably safer to […]
Can you use blades on Lexus cars or is there a factory coating?
Method 1: The only Lexus that has a factory coating on it is the NX300. Otherwise, no other models have one and it’s fine to use a blade to clean with on them.
How to save money in an auto tinting shop.
Method 1: Some say using a plotter is a good way to consistently save money on labor by allowing the machine to do the work for you. Finding a high-value film to use can also save a lot of cash in the long term. Some tinters find ways to be efficient with their use of […]
Glass exploded on a Honda Civic immediately after leaving the tint shop
Answer: There could have a massive drop in temperature that caused the glass to explode. If the tint shop is very warm while it’s well below freezing outside, this can put stress on older glass. For example, if the tinter heated up the glass with a heat gun while shrinking and then the customer quickly […]
How to remove the sweeps on a 2019 Ford Ranger
Answer: If you’re very comfortable pulling sweeps off in this manner, you can just “pop them off” by grabbing the top section of the panel, digging in with your tips from the top face, and pulling away. Eventually, the middle will come out and you can slowly pop it off. A safer method though is […]
How to pull the sweeps on a 2021 Mazda CX5 and 2021 Mazda 3.
Answer: Open the door and grab the top panel with your bare hands right in the center. Pull out enough so that it pops off, but not the whole thing – just a section in the middle. While holding the panel with one hand, stick your other hand in through the gap. You should be […]
How to put a blackout line on the backglass of a Camaro
Answer: If you take the glass out completely, you can easily straight edge cut a piece of blackout tint before replacing it. Lay out the piece, clean it thoroughly, then put the primer on. After letting the primer dry you can tint as normal. If you can’t take it out, then the easiest way […]
How to avoid bubbles appearing in tint jobs in cold/hot weather
Answer: Film takes two to four weeks to completely dry out during the dead of winter or the peak of summer. Some bubbles or “haziness” tend to appear during that period. If this is the case, these types of bubbles are harmless, will go away, and are not evidence of a bad tint job. Some […]
A windshield leaking after I tinted it? What happened?
Answer: There are a lot of variables in this situation that could be contributing to the leak in the windshield after it’s been tinted. If the vehicle has a sunroof, then the most common reason for a leaking windshield is that the drains for the sunroof are clogged with dirt. The sunroof drains are grooves […]
Can you put electrochromic film on cars?
Method 1: You can absolutely put electrochromic film on cars, and this product has been in use within the auto industry for a while. However, the film has to be manufactured in pieces per vehicle because cutting the film with a knife causes the chemicals to leak out. This means you can’t custom cut this […]
The easiest way to tint a 2021 Toyota Tundra
Method 1: A 20-inch roll will just be sufficient to do these models, but this is cutting it close. The easiest way to tint the back doors is to remove the lower sweep and go for a bottom-load tint job.
How to tint around the spoilers on Honda Civics.
Method 1: The easiest thing, if you have one, is to use a plotter. This will give you the cleanest cut. Method 2: The other way to deal with these spoilers is to remove them, which should take about 15 minutes. First, you must remove the wiper motor by removing the 10 mm bolt. […]
How to tint around the plastic latches on the windows of Ford Rangers
Method 1: Remove the latch completely, tint, and then add it back again. To remove the latch, take a straight pick and push out the pin from the latch that runs vertically. You can go from top to bottom or bottom to top. There is a V-shaped piece of metal inside that acts as […]
Can you prevent condensation on windows?
Method 1: If you are in a hot climate where you’re forced to use air conditioning to make your home, office, or business comparatively very cold, you will most likely experience condensation. The more drastic the difference in temperature is between the inside and the outside, the more difficult it will be to prevent. […]
Can the backglass on Plymouth Barracudas be done in one piece?
Method 1: Because of the round, tapered corners, these are extremely difficult to shrink and install in one piece, and should only be attempted by very experienced and confident tinters. Lesser experienced tinters should turn these models away, as not only is the tinting difficult but this glass is almost impossible to replace if it […]
How to prevent scratches on tint when rolling windows up on a 2018 Porsche Panameras?
Method 1: Remove door cards, and use an adhesive promoter to clean the plastic weatherstrip. Attach a 3/8ths wide strip of moleskin or felt. Then move forward and tint the car. Tint shops will often charge more for these models because of the extra time it takes to prepare the windows and the risk of […]
How to remove spoiler on a 2017 Honda Civic.
Method 1: The first thing you need to do is remove the wiper motor by unscrewing a 10 mm bolt. Next, remove the wiper by just jiggling and unsnapping it. Under that, there will be a large bolt that can be removed with a pair of pliers if you don’t have a big enough wrench. […]
What to do when a 2020 Dodge Ram won’t start after a tint job?
Method 1: If a 2020 Dodge Ram won’t start after a tint job, then you have to really hope you haven’t fried the ignition module under the dash. Those modules are about a $3000 fix from the dealership. This one of the main reasons why some tint shops won’t do these models; It’s not worth […]
How to cut out quarter windows for 88 Toyota Supra?
Method 1: Cut the top before you install. Then install and squeegee out the water – but not all the way to the sides yet. Using just a tiny bit of blade, cut around the sides. Take a card and force the water out and dry off with a paper towel. Method 2: You […]
How to choose tint levels for high sun levels.
Method 1: The larger the window, the more conscious you have to be about your VLT levels due to breakage. Always consult with your manufacturer or someone local who knows the climate.
How to fix a defective “Enter” button on a jaguar plotter?
Method 1: This usually happens because of issues in the module. There is no way to fix it except replace it with a new button. They cost around $100 and will be delivered by customer service.
How to tint a 2017 Dodge Challenger?
Method 1: The back glass can be more sensitive than other models so be careful with steel wool or anything else abrasive in your prep work, use a clay bar for the defrosters. The door panels can be removed by unscrewing the four screws under the latch. It’s best to pull the sweeps on this […]
How to trim or cut rubber gasket or lining on flat glass ?
Method 1: If the gasket is easy enough to pull out, save yourself the time of trimming it and just pull it out and push it back in afterward. If the glass is very tight or the gasket seems brittle, you may have to resort to trimming. If you’re comfortable with it, you can use […]
How to prevent bubbles on the quarter window dot matrix of BMW 4 Series
Method 1: When tinting, heat it up with a heat gun and firmly push with your finger and a microfiber towel. Method 2: Prep thoroughly with steel wool, or softly scrape with a blade until the dots are smoother. You can also try using small amounts of glue.
How long after getting a windshield replaced can you tint it?
Method 1: The way all shops work is different, depending on their process. Though conventional wisdom is usually around 1-3 days, it’s best not to touch any glass that’s under a week old. The urethane on each type of glass can be slightly different and needs to be able to fully cure before being tinted. […]
How to remove the door panel on a BMW 7 Series
Method 1: For the front doors, there are torque screws under the plungers that need to be removed. After they’ve been unscrewed, the panel should pop off. Method 2: For the back doors, you have to dig in with your fingertips to pop off the two-piece weather stripping at the top of the panel. […]
How to tint the backglass on a BMW i8
Method 1: Remove the glass and tint it, then put it back in. To remove the glass, pull the outside lower window trim by prying it with something. Inside the cavity are two yellow tabs. Insert your bulldozer inside and press against the yellow tabs. Once the tabs are unclipped, the whole window can slide […]
Can you tint the back window of an 88 Corvette convertible with Luxe?
Method 1: It’s not recommended to use luxe on these windows. It can stay on sometimes, but generally speaking, there is a high chance that it will fail rather quickly. Because of the way the plastic window contorts as it opens and closes, eventually the luxe will crease up, get bubbles, or start to lift. […]
How to tint over factory light gaps
Method 1: You can ask the customer what they prefer, but ultimately you can only go to the top of the glass or the beginning of the seam. Whichever way you do it, you’ll still leave that light gap.
How to protect the modules in 2019 Mercedes models while tinting.
Method 1: On both front doors of the CLA250 and C300 are holes in the paneling that lead to the modules. Remove the door panels and pull the small tabs off. Then stuff these holes with cloth, paper towels, or anything else laying around that can prevent the entry of moisture. For extra precaution, you […]
What to do about broken defroster lines and how to prevent it
Method 1: Some vehicles like certain Mercedes, Camaro, and Cayenne models have delicate defroster lines that can come off when taking off old tint film while not even leaving any leftover adhesive. Unfortunately, the only way to fix it is to pay for a new window or try to get the company to warranty it. […]
How to tint around the sensors of a 2020 Toyota Highlander
Method 1: Tint in three pieces. Prep the matrix with 400 grit sandpaper, clean thoroughly, and then stick the film from the window’s edge to the outer side of the sensor. For easier cuts, remove the plastic light and hand cut around it.
How to tint the dot Matrix on a Chevy Volt
Method 1: This matrix is actually relatively simple compared to the ones on other models. Sometimes it’s even possible to do no extra prep work to it. To be safe, it’s best to sand the matrix with fine steel wool while wet, and then tint over it as normal.
How to shrink the back glass of a Ford Focus without removing the spoiler
Method 1: Use the liner to cut your shape and use it as a guide to cut the film Method 2: Flip the film upside down to shrink, and then right side up to trim and touch up. Method 3: Dry shrink as much as you can, and then hand cut the bottom […]
How to prevent film from lifting on the bottom of a Honda Accord
Method 1: Keep in mind that there is a foam strip at the bottom of the back glass on Honda Accords. Most of the time, when the bottom of the backglass’ film is lifting up, it’s because the film is slightly butted up against the foam strip, and when water collects near the strip, it […]
How to prevent bubbles in the film around the defroster lines on a 2010 Nissan Altima
Method 1: If it’s an issue with your prep work, try focusing on using 0000 grit steel wool on the defrosters and thoroughly cleaning them afterwards. Put special focus where the lines curve upwards as this is where the peanuts are most likely to appear. Always spray afterwards with your mounting solution and squeegee it […]
The window won’t roll up on Nissan pickup truck after I removed the panel and rolled the window down. How to fix it
Method 1: If you’ve been rolling the window up and down on an older Nissan pickup truck while tinting it, it either came off its track, or the plastic tabs that connect to the actuator have snapped. There are small pieces of plastic that attach the actuator to the door. If they have broken or […]
After tinting with ceramic film, the window is foggy and blurry, especially in the morning. What happened?
Method 1: What you’re most likely experiencing is known as ‘low angle haze’ which can happen to carbon and ceramic window films. When light shines at a low angle, as it does during morning or evening sun, haziness will appear in the window because of microscopic particle density in the IR layer of the film. […]
How to tint around the felt on the back glass on the 2017 Volkswagen Golf Wagon
Method: The best way is to remove the hatch panels and just tape off the felt. To remove the panel, look for three clips. Two of them won’t come out until you slide the pillar upwards and use needlenose pliers to fetch them out. There will be holding till tabs that you have to put […]
How to remove the front door panels on a 2011 Volkswagen Jetta SportWagen
Method: There should be two torques, one behind the door handle and one in the middle of the door panel. The underside of the door has a plastic bolt that needs to be twisted off. The rest of the fasteners are just push tabs. You don’t always need to pull the whole panel to tint […]
How to tint a 2017 BMW i3
Method 1: The windshield is obviously very large, so it needs to be shrunk a lot. The doors are relatively tight, so it’s best to get those out of the way first. Before you tint the doors, check the sweeps – as some models have a little piece that can interfere with the film laying […]
How to prep glass before applying film
Method 1: Prep work will depend on the condition of the car; older cars will require more cleaning and perhaps more disassembling, whereas a brand new car will be cleaner and quicker to prep. On a brand new car, you can usually get away with pulling the sweeps (if necessary), spraying the glass, and then […]
Can you tint the back glass on a Corvette C8?
Method 1: Since the powerful engine is directly below the glass, it’s going to give off a lot of heat and put stress on the film. Although you can still tint this glass and have it last, it’s best not to warranty the job or at least explain the situation to the customer. If you […]
How to tint the back glass of a 2019 Porsche 911 Targa
Method 1: Open the hatch roughly halfway and keep it in place. Next, sit on the back of the trunk to reverse roll your film. Make sure you have shrunken it completely so the fingers don’t pop up on the inside. Since the limited space makes the inside of the glass so tight, cut your […]
How to fix a keyless system entry failure after tinting a Honda Civic Hatchback
Method 1: If you use a lot of water in the area surrounding the module in the door of the rear hatch, it can get wet and cause electronic malfunctions. Since these cars are so sensitive, always cover them up and don’t use more water or slip solution then you need. If you have an […]
How to remove water stains from the door panel on a Chevy Silverado
Method: Covering the panel or removing it altogether is the best way to remove water stains. But if you have stains after tinting, it is still possible to remove. First, spray the panel with Armor All and then wipe it with a white scrubby. You can also hit the stains with a heat gun and […]
How to tint the back glass on a Honda CRV
Method: If it’s an older model, it may be better to take the glass out completely, clean out the grime, tint, and then reinstall the glass. Regardless, you have to take out the wiper motor, the cable around the windshield, and the brake light. If you don’t have a plotter to cut around everything, cut […]
How to tint glass with uneven, jagged silicone or gasket.
Method 1: There is no way to get clean edges on gasket or silicon that has become jagged or uneven after years of deterioration. The only way tint it properly is to trim it straight with your blade, or cut it all off completely and redo it – either with new gasket or new caulking. […]
How to tint the back glass on a 1979 Camaro Z28
Method 1: This model is a lot easier if the glass is removed because you can stretch shrink it with clamps on the corners to prevent the film from lifting. If you have to do it in place, make a standard H pattern and be ready to heavily manipulate the film. First, lay your pattern […]
How to remove blade scratches on a 2020 Lexus NX 300
Method: The 2020 NX 300 has a coating on the inside of the glass that can make it easily scratchable. If you see a scratch, it’s most likely in the coating rather than the glass itself. It is possible to remove the coating. You will need to remove the entire coating on the glass, so […]
How to tint the back glass on a Crown Vic
Method: Cut your film long, at least a few inches on each end, and make relief cuts if needed. Tack the film down with an H pattern, and start heating and shrinking in the corners, keeping the fingers up and down. It’s important to keep the fingers vertical and split half of them to the […]
What is the darkest you can tint a windshield?
Method: This depends on the window and the state you’re in. For example, Alaska only allows 70% on the front side windows and 30% on the rear window. Wyoming on the other hand allows 28% on all windows, whether it’s the windshield, front windows, or back window. Exceptions are only made if you have medical […]
How to repair knife scratches on windshields
Method 1: If the scratch is light enough, it can be sanded down, and then polished out. But if you try this process on a bigger scratch, the amount of sanding and polishing you’ll have to do will create a dip in the glass causing optical distortions. In situations where the scratch is too deep, […]
How to tint the windshield of a 2020 GMC Denali
Method 1: Before doing anything keep in mind that there is a computer behind the glove box at the base of a pillar. The dealership cost to replace these computers is $6,000, so always thoroughly cover your dash, use a soak rope and towels, and try not to use more water than you need on […]
How to store your clean rags and towels for tinting
Method 1: The simplest way is to just keep them in boxes or buckets, unfolded; one for dirty rags and one for clean. You can also use drawers. To minimize the collection of dust, roll them up and then stack your rolled rags on shelves. Use a laundry style basket for dirty rags so they […]
Can you tint the windshield on a Subaru Crosstrek with EyeSight?
Method 1: Subaru completely recommends against this and many tinters refuse to tint over these windshields. That being said, other tinters decide to go right ahead. It has been reported in the past that a tint job over the EyeSight will make the cameras and sensors malfunction, causing accidents or rear ends. It is possible […]
How to shrink the windshield of a 2015 Lincoln MKZ
Method 1: The shape of the window makes it easy to get bonds or creases in the bottom and top corners after you tack it. To avoid this and get a clean shrink, use a drier sheet and wet only the center line. Next, go ahead and dry shrink it as normal.
How to tint a 2010 Volkswagen Beetle
Method 1: Remove panels and sweeps on all the doors to keep it cleaner and avoid light gaps. The roundness of the back glass makes it the most difficult part of the car. Cut the film for the back glass with lots of excess and pull shrink it past the ceramic all the way to […]
How to tint the back glass of a 2016 Chevy Camaro
Method 1: Always be conscious of the computer on the left side of the back trunk. Water will run into it and destroy it so make sure to cover it up nicely before tinting. The back windows are very tight, so unless you’re an experienced tinter, remove the back panel before tinting. If the car […]
How to tint over the matrix on a Chevy Volt hatchback
Method 1: Sand the dots down with fine steel wool first. Tinting the matrix on Chevy Volts usually requires more heat than normal, so consider using lots of heat or using your heat gun on a higher temperature if the film isn’t sticking right. Apply lots of pressure and squeegee upwards. Glue can also help […]
How to tint the front doors on a 2014 Chevy Impala
Method 1: First remove the door panels by undoing the 7mm screw just above the interior handle. Then you can unclip the top of the panel, which gives you access to the gasket. Pull the gasket and cover your door if necessary. Then begin the tinting process as normal. Replace gaskets and panel components in […]
How to avoid staining door panels when tinting
Method 1: Sometimes removing panels completely is the best way to avoid damaging door panels while tinting, but it’s not always practical. When tinting with the door panels in place, cover them up with specially made car door cover. They can either be draped right over the top of the window cavity or be fastened […]
How to tint the front quarter windows on a Honda Pilot
Method 1: Trim the inside gasket on the side closest to the roll-up window at a 45-degree angle and slide it in with lots of slip solution. Try creating your pattern by cutting a liner on the outside of the car. You can also cut the liner on your film on a peelboard or other […]
How to remove the rearview mirror on a 2017 Honda Accord
Method 1: Grab the square plastic piece that connects the mirror to the glass, and turn it counterclockwise. It will pop off and come down. You will then see a lever under the mirror. Push that lever down and then slide the mirror off. Don’t pull on the mirror, only slide it after the lever […]
How to tint the backglass of a 2019 Honda Civic when there’s a spoiler on it
Method 1: The best thing to do is just to remove the spoiler. The spoiler can be removed by removing the plastic cap from the inside. Remove the 4 bolts holding the 2 handles. Then, remove the 2 housings for the lights on the trunk. You will also have to remove the wiper and the […]
Traction control light, tire monitor light, and echo lights are all on after tinting a 2017 Honda Accord. How to make them turn off.
Method 1: The Honda Accords are programmed to notify you when the battery has been drained to critical levels. So if you’ve had the doors open or lights on for an extended period of time or if it goes dead and you have to jump it, those lights will usually be on. Just drive it […]
How to insert film into the rear quarter windows of a 2020 Honda Passport
Method 1: Use your stick to get pop the black cover off, and then use your fingers to pull the rubber off the glass while liberally spraying your solution into the gasket. This should give you enough of a gap and lubrication to slide your film into the gasket.
How to tint the back quarter windows of a 2007 Ford Fusion
Method 1: The easiest way to tint these quarter windows is to leave them in place and trim the rubber about a sixteenth of an inch from the high corner downwards along the rounded corner. Leave your knife blade out only a couple of clicks, and slowly slice the rubber while being careful not to […]
How to tint the deep pocket windows on older Ford pickup trucks
Method 1: Make a small back cut on the inside of the rubber lining to make it completely uniform. Cut out your pattern with about an eighth of an inch past the rubber and then cut your sides and top evenly. It should go right in without any issue. Method 2: If you have […]
How to tint the front quarter windows on a Ford Transit 150/250 without a plotter
Method 1: Cutting out the film for these quarter windows by hand can be a lot faster than using your computer. If you’re not confident about hand cutting it on the vehicle, try creating a guide by cutting a pattern out an old release liner, and then using that to cut out the quarter. Once […]
How to prevent failure of tint jobs on Ford Fusions 2013 and up
Method 1: Many tinters agree that most tint jobs on Ford Fusions will fail within two years, regardless of the quality of the film or the conditions it is exposed to. These issues usually arise only with the 2013 models and newer ones. It is common for tint shops to void the warranty on these […]
How to tint a Lexus IS 350
Method 1: Because of the finicky nature of the gaskets and seals, it’s always better to remove the door panels before tinting and shrinking. The panels can be removed by accessing the two screws on the bottom. Once the panel is removed, remove the bottom load as well. With the bottom load and panel removed, […]
How to quote for a 1987 Airstream trailer
Method 1: These trailers have a total of 16 panels, so they’re much more time-consuming. However, the tinting process is relatively simple compared to similar models. Most tinters will charge somewhere between $1100 and $1500.
How to identify the causes of large peanuts
Method 1: Peanuts aren’t always caused by bad tinting jobs. Sometimes if a sticker is placed on top of the film and then ripped off, the force of ripping off the sticker can pull the film from the glass. Similarly, too much force from a suction cup can also lift the film up from the […]
How to peel film on a mobile-tinting job
Method 1: Bring a piece of plexiglass and lay it down somewhere or lean against something. Method 2: Use a folding table and stand it upright Method 3: Sometimes it’s easier to just peel your film on top of the car. Peel the film for the front doors on the rear door, and […]
How to tint the back passenger windows on a 1997 Lexus LS400.
Method 1: Lay your film over and then cut on the left side. Next, shift the film over the top of the dots about half an inch. Now cut the bottom and the left side of the film. Slide your film over so it just exceeds the dots, and then bump it downward about a […]
How to tint the front passenger doors of a Ford GT
Method 1: Take the seals out of the bottom load and tack down one side of your film. With your heat gun on low, slowly shrink the other side of the film. With motions similar to that of back window shrinking, move across slowly and then gradually work your way down. You may get creases […]
How to remove the third brake light on 2019 Volvo S60.
Method 1: Remove the two screws on either side and take the panel off. Then remove the clips on the wiring and disconnect the bulb.
How to avoid creasing on the back glass of a 2020 Toyota Corolla.
Method 1: The most common reason for getting creases on the back glass of a 2020 Toyota Corolla is from doing an H pattern. Instead of using an H pattern, tack the film down with one horizontal line dividing the top from the bottom sections. When it comes to the top corners, don’t pull from […]
How to strip off decades-old CDA adhesive
Method 1: Very old adhesive can be the most stubborn to remove. First, try a quality adhesive remover with a sharp blade. If you don’t have access to a high-quality adhesive remover, sometimes paint thinner, acetone, or oven cleaner will actually do a better job than the adhesive remover itself. Method 2: If scraping […]
How to remove the sweeps on a Lexus LC500
Method 1: The sweeps are clipped into the panel from the back, so in order to access them and get them back on, you need to remove the panels altogether. There are 2 screws on the driver side and four screws on the passenger side. The pins are embedded in the rubber. These clip holders […]
How to tint the back window on a Corvette C6 XPEL XR
Method 1: After placing your H pattern, lay your film down on the window with some excess. Once the film is tacked down, cut 4-6 inch relief cuts from the back corner of the window to about 3/4s of the way down towards the front doors. Then start shrinking with your heat gun, starting at […]
How to tint the front quarter glass on a 2020 Honda Pilot
Method 1: One option is to remove the glass. There are 2 bolts behind the door panel and a screw on the top which are easy to pull. Method 2: If you prefer to leave the glass in while tinting, you can loosen the seals while you’re cleaning it. Then stick a card into […]
How to tint a Ford Fusion 2013 and up
Method 1: Many tinters have issues with film failing on these models, especially the rear glass. Some believe it is the angle of the rear glass, while others believe that the defrosters are too thick, which causes them to get too hot when they’re turned on. There is a coating on the glass that causes […]
How to tint the wings of a Ford Transit Connect
Method 1: Most tinters find using a plotter to be easier than hand cutting on these models. Removing the panel and the sweeps will make things much smoother as well. Loosen up the seals, slip in a bone stick and slide it around until there’s enough space to slip your film in. Then place your […]
How to tint a 1990 Toyota Sera
Method: Most tinters will opt to shrink in a side to side manner rather than top to bottom. The doors can be done with a 30-inch roll. The rear screen can be done in one piece, shrunk up and down. Sometimes having a second person assisting with the tint on the rear screen makes the […]
How to get water out of the back windows of any vehicle
Method 1: The most popular tool to get water out of the back windows is a bulldozer, but sometimes its not always practical or sufficient. Another helpful tool is a side swipe. You can also get pretty creative with certain blades or something similar.
How to tint a 2016 Jaguar F-Type
Method 1: This is one of the easier models so just tint as normal. Some tinters prefer preheating the door windows. Make sure to tuck the film under the rubber gaskets with your preferred tool.
How to tint a 57 Chevy without removing the glass
Method: Cut your film and then shrink it on the outside. Don’t ever use a torch on this model as the glass will break fairly easily. Cut a 1/16th inch gap on the bottom edge of the rear glass and a hairline gap around the whole thing to prevent the film from sucking up debris. […]
How to avoid water streaks on the back window of a Tesla
Method 1: Use a soak rope and make sure to thoroughly insert it as tightly as possible. After a clean squeegee job, leave the soak rope in for a few minutes. If you pull out the soak rope right after squeegeeing, the rope will slide against your film and this is what causes the streaks. […]
Preventing contamination of tint film
Method 1: There are many things you can and should do to prevent contamination of your film. The first thing to consider is your environment. If you’re outside, debris can fly onto your glass. If you’re in a dusty environment, you will also be more prone to debris. In debris-prone environments, you have to be […]
How to remove the adhesive from a roll of film
Method 1: Use your fingers. For more stubborn rolls, bite it to put a little dent in it, and then pick at it with your fingers. Method 2: Pry it with a fine Olfa blade or something similar
Tinting the side windows of a 1992 Mercury Grand Marquis
Method 1: Many tinters have trouble slipping the film inside the side window seals. To do this effectively, you can pop the tops of the door panels off, and then pull the seals. Once the seals are out, you can clean underneath and tint as normal. The seals will slide back in the way they […]
Tinting the windshield of a 2019 Nissan Elantra.
Method 1: The main difficulties with Elantra windshields are the tight top corners. There is a lot to shrink in a really small amount of surface area. A thicker film will exacerbate these problems, so don’t use a film that is thicker than you need. In order to prevent pockets and creases, try tacking the […]
How to remove glue from back glass
Method 1: Sometimes there is no easy way. First, scrub it with fine steel wool and soapy water. This should remove most of the glue. Method 2: Try using a razor blade with soap solution and a little elbow grease. Method 3: There are also various adhesive/glue removers specifically designed for this process. […]
How to tint the back window of a 1978-1987 El Camino
Method 1: Because of the tight narrow corners, many tinters will charge a lot for these. Most of the time, it’s easier just to remove the glass, shrink it from the inside, and then install. Once installed, trim a ⅜ inch around the perimeter to tale the glue into account. Then let it dry and […]
Tinting a side window without removing the gasket or panel
Method 1: If removing the gasket is not possible, there are a number of possible solutions. The first thing you can do is get someone on the other side of the window to pull on it with a suction cup in order to create a gap between the glass and the gasket. Then use a […]
Can I still tint a window if it’s chipped?
Method 1: You can still tint a window if it’s chipped, but you have to do it from the opposite side of the chip. The chip may also become more visible when the dark color of the tint contrasts with the whiteish color of the chipped glass. Car owners should be advised that replacing the […]
What size roll of film should I use for the back window of a 2000 Mitsubishi Eclipse?
Method 1: A 36-inch roll on a back window will be adequate for every Mitsubishi Eclipse model from the year 2000 and up.
Why are there small dots in my tint?
Method 1: If you’re seeing the little dots inside your film after you tint, it just means the film was contaminated by dirt or dust. Make sure you’re wiping down your glass with a microfiber towel and wiping in only one direction. You also need to make sure you’re spraying and squeegeeing. If specks/dots are […]
The best way to store window film.
Method 1: Film rolls should rest on soft surface shelves or racks so as to not put stress on them and cause creases or folds. You can glue foam to shelves, or for a more economical method, you can buy vertical closet racks and put them on your wall side to side, and then use […]
Removing old film on the back window of a 1996 Toyota Camry without damaging defroster lines.
Method 1: Repeated scraping will eventually damage or remove the defroster lines, and scraping around them is nearly impossible. The best way to remove an old film is to use the trash bag method: Soak the whole window in heavy ammonia and then cover it with a black trash bag. Then place the car in […]
Tinting rear window dot matrix on a 2016 Chevy Camaro
Method 1: These dot matrices are prone to heater lines, so it’s important to go slow and shrink evenly. Method 2: Prep work is probably the most important for the dot matrix. Thoroughly scrub down with steel wool or a clay bar.
Tinting side windows of 2021 Kia K5.
Method 1: The sweeps are easy to remove as normal but the vertical side seals are very tight. If you need to remove the side seals it’s possible to do so by prying the top out a bit and then sliding them upwards. Method 2: To tint with seals in place, you will have […]
Can you tint only the top half of a windshield?
Method 1: There is a risk of uneven heat stress on the glass, but windshields on new models of high-end vehicles – for example, a Tesla Model X – are not as at risk for this. In general, it’s completely fine and problems are uncommon.
How to tint the quarter windows on a 2016 Honda Accord.
Method 1: One option is to take an extra 5 minutes to remove the glass to tint. This will eliminate all possibilities of light gaps. This can be done by slipping a lubricated equalizer shield under the side of the glass next to the door. The whole piece of glass will pop out with the […]
Removing the sweeps on a 2020 Chevy Colorado
Method 1: It is possible to remove the sweeps on a 2020 Chevy Colorado but it is not advisable due to the risk factor of cracking the door panel. It is still possible to tint without removing by a good tape job and extra slip solution.
How to tint the side windows on newer models of the Jeep Wrangler (with electric windows)
Method 1: It is more difficult to tint without removing the seals, but it is possible. The vertical side seals are harder to deal with than the bottom ones. Tape the vertical side seals and use a lot of your slip solution on those seals, getting it extra wet and lubricated so the film can […]
How to choose a tint level for a customer if they don’t know.
Method 1: First and foremost consider the legal restrictions in your state. Many people who drive high-end models prefer not to be seen, and darker tints on lower-end models can look a bit ‘tacky’ to many. Also, consider what you have to match the other windows to. Most high-end vehicles, and also many trucks and […]
How to prevent creases and peanuts on defroster lines of back glass.
Method 1: Start with good prep, and make sure you prep the defroster lines thoroughly with either steel wool or a clay bar. Method 2: If you’re wet shrinking, be more conservative with your slip solution. Peanuts are usually just tension points caused by an uneven shrinking, so make sure to take your time […]
How to dry out a car if it is malfunctioning after a tint job due to a leak.
Method 1: Preventing this from happening with soak ropes and dash towels is the first step. Otherwise, leave the car running with the heater blowing in foot position. If you have fans, set them up inside as well.
How to tint stationary side windows on Mazda 3
Method 1: These can be tinted without removing by sticking something between the interior gasket and the glass like a bulldozer or pry bar, creating a gap and then cutting the film long and hand-cut the rest. Stick the excess film in the gap you created, and then remove your bulldozer squeegee or pry bar. […]
How to remove failed tint film filled with bubbles
Method 1: Loosen the film with a steamer and then scrape off with razor blade. Clean off any remaining debris with your window cleaner Method 2: If you don’t have a steamer, soak the glass in Windex or Ammonia and then cover with a black trash bag. Store the car somewhere hot or in […]
How to tint plastic rear windows on Audi convertible
Method 1: To avoid peeling after years of opening and closing the top, use a static cling film. Method 2: Tint it with a smoke job instead
How to use clay bars.
Method 1: Liberally spray your slip solution and then lightly scrub left to ride with the clay bar. Keep the window wet with your slip solution the entire time. To clean the clay bar, just run under warm water to get rid of the grit. You can store in a Ziploc bag. With proper care […]
How much does it cost to ceramic tint an entire Mercedes work van?
Method 1: Depending on your state, it could be as little as $700 or as much as $1200
How to prep the side dots on BMW windows
Method 1: If you’re going to sand, wet sanding with 0000 steel wool is probably the most abrasive you should use on it to avoid scratches. Method 2: Many tinters won’t touch them with a sander and instead will just rub them down with a scrub pad, especially on new models with cleaner surfaces. […]
How to cut out side windows on a 1988 GMC truck
Method 1: If you’re confident in your cutting abilities, leave the window in and cut around the screw caps on the glass and tint normally. Method 2: Remove the window by taking off the screw caps. If the screws look like they might strip, you can try heating them a bit with a heat […]
How to tint a 2016 Maserati Ghibli
Method 1: If you want to remove the glass, you can do so by removing the 4 10mm screws underneath the shelf. However, it is fully possible to tint without removing anything and tinting as normal. Using a bulldozer squeegee helps with the tight spaces on the rear window.
Will putting a windshield brow on a 2019 Subaru Ascent affect the front camera system?
Method 1: Depending on the level of tint, the cameras may or may not be affected. It is best not to go darker than 70%. However, Subaru may void the customer’s warranty if you do put a brow in front of the cameras.
How to tint a 1995 Oldsmobile Cutlass Supreme
Method 1: This car is one of the most difficult models to tint because of the curvy dovetails on the bottom corners of the rear window, so many tinters will either refuse or charge a significant premium to do it. Tinters also may not offer a warranty. In order to tint all in one piece, […]
How to remove rear view mirror from windshield of Ford F-150 and most other Fords
Method 1: The mirror will slide upwards from the clip that is adhered to the windshield. Insert a right-angle hook bar in the very center between the mirror and the clip on the windshield. Tap the hook bar inside with a small rubber mallet or even the handle of a screwdriver so you don’t damage […]
How to stop the Tesla Model X from closing up automatically and doing other things automatically that interfere with the tinting process?
Method 1: Take the battery out of the key remote.
How to tint Jaguar XJL
Method 1: When pulling the rear deck, there is an alignment peg directly below the brake light. This can become a nuisance during the tinting process, and you may need to cut some of it off in order to reinstall. Method 2: Be aware that the seals are very tight, including the rear 1/4s. […]
How to avoid pinch marks when using a plotter
Method 1: Make sure the blade holder isn’t faulty. The spinning blade can become caught or snagged if the holder isn’t gripping properly. Method 2: Examine the pinch rollers. Make sure that they are locked down and firmly pressing down when the plotter is operating. If the pinch rollers are faulty, it can cause […]
How to tint a 2007 Chevrolet Tahoe front window by going around the sensor
Method 1: Cut around the sensor instead of trying to remove it. Method 2: Unplug the wires, remove the interior mirror, and tint around the sensor. Method 3: There are metal tabs that you can wedge out at either side. The sensor is affixed to the glass with a gel pad. This sticky […]
How to use a soakrope before windshield tinting
Method 1: After protecting the dashboard with a microfiber towel, use a flat object such as a spatula or plastic wall scraper to insert the soakrope as deep as you can in between the glass and its perimeter. Start in the middle and work your way to the outsides. Remove the rope afterwards.
What is the easiest way to shrink a back window film?
Method 1: Use a dryer sheet, rub an “H” pattern with a damp sponge and then dry shrink. Method 2: For a non-toxic method, use a soap bar on a damp towel, and then blow it dry, and then dry shrink. Method 3: In place of dryer sheets or soap, use a heat […]
How to remove CDF adhesive film from a window
Method 1: Cut 4-inch strips and peel off what you can. Make sure the glass is wet with soapy water, and then use a single-edged wall scraper with stainless steel blades to scrape away the residual pieces. Afterward, do a last wipe-down with acetone. If you plan on putting HPR or PS adhesive on next, […]
How to preview to a customer what a design tint will look like for doors or windows
Method 1: Print out a miniature version and stick it to a window or some glass. Take a photo of them, and then upload the photos to photoshop and edit in the door, car, or window frame. Print out or email to clients.
How to prevent tint film from getting caught while rolling windows up and down
Method 1: Use a torch to lightly melt and coating or residue to smooth out the surface. Method 2: Use polish to remove any hydrophobic coatings.
How to use a steam to remove film from inside of the window
Method 1: Allowing the steamer to do the work for you, start at the corner and slow pull with your hand as the steam disconnects the film from the window. Method 2: Using the more efficient ‘Curtain Technique’, start at the two top corners and remove the film until there is one straight horizontal […]
How to remove trapped hairs from under film.
Method 1: Assuming you’ve caught it before drying, use a marker to circle the hair so you don’t lose track of it. Start peeling from the nearest corner and thoroughly spray the window with your solution. Use your finger to remove hair, and then spray the area again. Reapply the film and then use your […]
How to prevent creases in the bottom corners of 2008 Corvette back glass
Method 1: Cut the film long and put relief cuts on the excess film. This will allow you to pull the bottom corners tight without causing bubbles or creases.
How to do mobile tint installs on cars
Method 1: Get the car out of the wind or use a camping-style tent to put the car under to prevent wind and falling debris. Thoroughly wipe down any surface that you plan on tinting before and during your installation. If you can, work quickly to reduce the chance of hair/debris landing under the film.
How to tint a 2020 Dodge Durango
Method: The glass on the inside of the windshield on the 2020 Dodge Durango will scratch when scraped with a stainless steel blade, so if you need to hand cut the film, use a cheaper metal blade. If you need to scrape the window, use an alternative like steel wool. It’s also imperative to properly […]
After replacing a windshield, how long should you wait to tint it?
Method 1: Depending on the type of adhesive used, you can get away with doing it a few minutes afterwards, but most technicians will wait 2 days to 1 week before tinting.
How to tint 1954 Chevy truck corner windows
Method 1: Shrink to the sides with the windows in, keeping it clean with glue. Method 2: Cutting the film long, tack it down in the middle of the bend and then pull shrink the sides. Try using a jig or clamps in order to keep the window still Method 3: Some corner […]
How to remove the glass from a 2018 Kubota skid steer.
Method 1: Find the screws on the edges to remove the vertical bars, then slide the glass out sideways.
What’s the typical price for honeycomb tail lights?
Method 1: Depending on the car and whether or not you want it on side and rear reflectors as well, it could be anywhere from $100 to $300 a set.
How to avoid peanuts on a Nissan Altima
Method 1: Scrub with extra fine steel wool and alcohol Method 2: Use a clay bar.
Tips for removing hydrophobic coating on the windshield
Option A.) Burn off the coating with a torch. This can be dangerous in certain circumstances, so use a small torch (the kind chefs use to make creme brulee). Option B.) There are specialized products that are made specifically for removing this hydrophobic coating. If you don’t have access to these products, try stove […]
How to deal with inspection stickers and toll tags on the glass.
Option A.) Remove the inspection stickers prior to installation. After the installation is complete, carefully reapply the sticker. This way, it’s easier to remove stickers and add new ones without removing the film. When customers need to add/remove a sticker, tell them to come in and I’ll do it for them. This ensures the film […]
How to tint a sunroof.
Option A.) Explain to the customer that there is a possibility of the sunroof shattering before installation. Option B.) Only tint sunroofs with tempered glass. This results in a lower possibility of shattering. Option C.) Use a plotter when tinting sunroofs.
How to tint the plastic windows on old Jeeps.
Option A.) Order new windows from the manufacturer that are tinted. These zip into place. Option B.) Various types of light films and wraps are suitable for Jeep plastic windows. Option C.) Remove the entire top, lay it flat on the ground, and tint it like you would any other window. Remember to […]
How many different types of film should you keep in your window tinting business?
Option A.) Carry three different types: A budget type, a “standard” type,” and an expensive type. This will allow you to appeal to a range of different customers who have different priorities and budgets.
How to fix a steamer that isn’t putting out any steam?
Option A.) Make sure it’s not overfilled with water. Option B.) Lay the nozzle on the ground, bend the chrome ring on the hose, and let the water drain and sputter for a few minutes. Option C.) Sometimes, you need to wait up to 25 minutes for the steamer to get hot. You […]
How to tint Corvette C3 rear windows and “T tops.”
Method 1: Use a three-piece approach for the rear window. Method 2: Remove the passenger seat first. Then go in headfirst and tint the window while upside down (on your back).
What is the best way to cut glare strips with a plotter?
Method 1: Stack the glare strips on top of each other on a 20-inch roll. Method 2: Set up a custom width on your cutting table. Method 3: Take a 36-inch roll and cut it into three 12-inch sections.
How to remove minor scratches from window tint.
Method 1: The best way to deal with this issue is to remove the scratched film and replace with new film. Method 2: Buff the scratched film. Method 3: Spray the affected area with ammonia. Then take steel wool and scrub the area until the scratches fade away.
How to remove brake light on BMW Series 6
Method 1: Push metal tabs out with a small flathead screwdriver. Slide the brake light from the inside out through the small hole covering. When you’re ready to put the brake lights back, slide it back in – no tools required.
How to tint the small triangular windows on a 2020 Volkswagen Golf GTI.
Method 1: Put headlight smoke film on the outside. Method 2: Use two spatulas on either side, with one spatula holding the film in place and another pushing the water out. Choose spatulas that have a significant amount of flex to make the tinting easier. Method 3: Create your own custom tool that […]
How to tint the back window on a 2019 Toyota Tundra.
Method 1: Make sure the window is clear from any obstructions. Hold the “window down” button for ten seconds. Hold the “window up” button for ten seconds. Finally, hold the “window down” button once again for a further ten seconds. This should deal with any issues.
How to pull gaskets/sweeps from 2020 GMC/Chevy Trucks without removing the entire door panel.
Method 1: Take the trim level into account. If the trim does not feature woodgrain or chrome, then you can pull sweeps without an issue. If the time does feature woodgrain or chrome, then you cannot pull the sweeps without removing the entire door panel. Method 2: Newer models have an added lip that […]
I’m working with an old, fragile truck. It has brittle gaskets and there’s even duct tape placed on random spots. What’s the best way to approach this job?
Answer A.) Cut one side first. Then, slide it over about ¼ of an inch on the other side for a clean install. Answer B.) First, you need to go in and trim the inside gasket and cut the wing. Then, you need to thoroughly clean the area and let it dry before applying […]
I’m having trouble with my VQ Plotter. After sliding the head to one side, I’m noticing that my side cutting is cutting while the actual blade itself is not. I’ve reset the machine and recalibrated the blade, but nothing seems to be working. Any suggestions?
Answer A.) When you slide it all the way to the side like that, it engages the slitter. Sometimes, the slitter can get stuck as a result. Take the cover off and see what’s causing the slitter to become stuck.
I’m having trouble with sliding door windows on a Toyota Sienna. Any tips?
Answer A.) First, pop the panel back slightly. Then, go in and pull the seal. Answer B.) After you’ve popped the panel back, wedge the corners. Afterwards, you can actually sit in the car and bottom load for a clean install. Answer C.) There’s a small screw at the latch. Take it out, […]
Help! I had to redo my film, and when I removed it, the defrosters came off the window while attached to the film. What do I do now?
Answer A.) Speak to your customer and tell them what happened. If it’s a concern for them, you may have to replace the entire window for them. Answer B.) There’s not much you can do now. However, in the future you might want to let your customers know that you can’t guarantee their defrosters […]
What’s the best way to approach the back glass on a 2002 Trans Am?
Answer A.) Use the wet shrinking technique. Leave the center as a large bubble first, or pull it down from both sides. Answer B.) This is actually easier than it looks. No shrinking is required if you take your time, wet the entire surface, and card out all the water.
Any tips for tinting a Tesla Model Y? The sunroof looks like it could be quite challenging…
Answer A.) You may have to remove some of the panels to ensure a clean install. Answer B.) Make sure to cover the sides with plastic or towels if you’re working on the roof.
I’m seeing newer car models with a built-camera for driver-assisted technology near the windshield. Is it okay to remove the camera or get it wet?
Answer A.) When tinting windows with a camera nearby, it’s important that you don’t get it wet. This is especially true when you’re dealing with driver-assisted technology since this is safety equipment designed to protect the driver. Answer B.) Whatever you do, don’t tamper with the camera in any way. Doing so could make […]
How do I deal with the seals on older Jeep models?
Answer A.) First, fully clean the seals with a scrubby. Then, cut the films dead on the outside for a clean install. Answer B.) You can remove the seals by pushing them out and then rope them back in when you’re finished. Just be sure to loosen or remove the interior panels first. […]
How do I get the film to lay down on the back glass of a Ford Edge?
Answer A.) Spray it with a mixture of alcohol and water. Answer B.) Clean it with ammonia and go over it with steel wool. Answer C.) Heat the outside of the window while applying pressure. Answer D.) Go over it with a copper mesh pad. Answer E.) Wet sand the blackout […]
How to stop film from peeling back on a new Ford F-150.
Option A.) Don’t use too much soap in your slip solution. Option B.) Go the extra mile when it comes to prepping the window. Scrub harder, and make sure to hit the small dots before installation. Option C.) Do not over shrink. Option D.) Do not use sandpaper. Option E.) When […]
How to shrink the back glass of a Kia Soul.
Option A.) Dry shrink it. If you’re using an H-pattern, this might cause issues. An easier method is to simply tack it straight across. Also, let the edges float and put some air under the corners with the heat gun if you’re having issues with the corners. Option B.) Do a wet line directly […]
General tips for tinting a 2020 Audi A7.
Option A.) The defroster tabs on this car are hidden behind the panels on the hatch. Avoid jamming your squeegee past the plastic trim. This might end up damaging the defroster tabs. Option B.) The seals are pretty tight, but this is actually a pretty easy car to tint overall because the windows are […]
General tips for tinting a C8 Corvette.
Option A.) Don’t bother tinting the window covering the engine. It’ll inevitably fail. Option B.) Watch out for the back window, as it can be a little tricky to maneuver in that tight space. Option C.) Tinting the visor can be a potential issue, as there’s a built-in dashboard cam. A 5% film […]
I’m about to tint an Audi A8 L. Is there anything I should look out for? Any general tips?
Answer A.) This car can be a little tricky. First off, you can’t really remove the headrests, and this leaves you with almost no room to install film on the back glass. In addition, the rear windows have seals that you have to avoid when you tint. Answer B.) Watch out for water dripping […]
What are the downsides to bottom loading?
Answer A.) Bottom loading can lead to costly mistakes if you’re inexperienced. You can lose a lot of money if you don’t know what you’re doing, or if you don’t understand how the panels work. That being said, the best way to learn is to jump in headfirst. Answer B.) Sometimes it’s better to […]
How do I stop pinch points from showing up in the final product?
Answer A.) There’s no easy way to eliminate visible pinch points on the final product, but bottom loading has provided good results for me personally. When bottom loading, you may want to pull sweeps out for even cleaner results. Answer B.) Pinch points are relatively normal, and they go away with heat. That being said, […]
Any general tips for tinting a 68-72 Chevrolet Chevelle?
Answer A.) The back window doesn’t require much shrink. Just make sure you carefully examine the glass before you begin installation. Typically, these cars have silicon all over the place. It might be a good idea to cut just a tad short. Answer B.) These cars have a reputation for accumulating dirt, so make […]
I’m new to window tinting, and I want to practice on a car before I start working with real clients. Are there any particular cars that are easier than others. What’s a good “training car?”
Answer A.) Just head to the junkyard and buy a broken down car for cheap. If you scratch it or make mistakes, it’s no big deal. Answer B.) The back windows of SUVs are typically some of the easiest areas to tint. If you wanted to give it a try, I’d recommend starting with […]
My customer is complaining about a “squeaky window.” When they pull the side windows up and down, they say there’s a squeaking sound that wasn’t there before. What should I do?
Answer A.) Try cleaning the outside seal with a tri-edge and slip. This should solve the issue. Answer B.) Sometimes, the molding can get dry and creaky due to residue from dried soapy solution. To deal with this issue, put some silicone spray on a paper towel and emulsify the rubber. This should help […]
Is it a good idea to put more film over an existing layer of tint?
Most professionals will tell you that it’s best to remove the existing tint before you start your work. With this approach, you can guarantee your work without having to worry about existing defects from someone else’s job. That being said, the customer is always right. If they insist that they want a new layer […]
Do I need to maintain my tank for window tinting?
Proper maintenance of your tank goes a long way. Some tinters prefer to power wash the inside and then wipe the inside. Others simply rinse it out or soak with warm, soapy water. In any case, you should aim to clean your tank at least once a month.
What’s a good mix ratio for a tint slime mixture?
As a general rule, a ratio of 2 ounces to 3 gallons is a solid choice. Some tinters like to mix in a few drops of dish soap or baby shampoo as well.
What’s a good plastic window scraper blade?
One of the best brands out there today is Gator Blade. Many professional tinters out there today swear by them.
What’s a good piece of cutting software?
Many professional window tinters use Computer Cut. While there are other options out there, Computer Cut is a solid choice.
Is it true that having a car with a tinted windshield is illegal?
Laws differ from state to state, but it’s generally illegal to completely tint a front windshield in the United States. Remember, it’s the customer’s responsibility to adhere to the law when they operate their vehicle, not yours. That being said, if a customer requests a window tinting service that prevents their car from being street […]
Is it true that too much heat can cause a windshield to crack and break?
Yes, this is true. You can avoid this by keeping your heating gun mobile, and not keeping it in one location for too long. In addition, you might want to look over the windshield for small, pre-existing “spiderweb” cracks before you begin work. If you spot them, you should notify your customer. A soak rope […]
What’s the best way to get a good “before and after” photograph of my hard work?
Although photographs are an excellent way to promote and advertise your services, certain lighting may not be ideal for “showing off” your finished window tinting jobs. For best results, simply photograph the car in the sunlight. Alternatively, some tinters claim that LED lighting helps cameras pick up the added layers of film more easily.
What should I do if I’m having trouble making accurate cuts?
A good solution is to use some clear lining and trace out a template using a sharpie. Using this template, you can ensure that your cuts are accurate every time.
What can I do to avoid film peeling at the top of windows?
In some cases, customers might be rolling down their windows too early after the installation has been completed. Politely ask them to wait longer before rolling their windows down in the future. If the customer insists that they’re waiting long enough and it’s still an issue, make sure to heat the top edge of the […]
Is it beneficial to remove the spoilers on sports cars before installing window film?
Yes, removing the spoiler is usually a good idea if things seem tricky otherwise. Anything that gives you more room to maneuver is going to be a big help.
What should I do if there’s a bubble on my window that just won’t go away?
There are a number of things you can try. First of all, you might want to clean the window once again. Sometimes, cleaning the window three or four times is necessary. Defrosters might also be the root of the issue, especially on back windows. You can sand down the defrosters or go over them with […]
Can the temperature affect my window tinting jobs?
Yes. During hot days, you might want to work in the shade. If this isn’t possible, add more tint slip or slime to your bottle. The opposite may be necessary in cold temperatures. Many window tinters like to add dish soap or baby shampoo to their dish soap to their squirt bottles.
Why does the rear window appear lighter even though I’m using the same film for each window?
Generally speaking, the rear window will always look slightly lighter, even though the exact same film is used. You can inform your customers that this is something of an optical illusion. The dynamics of certain windows and the type of lighting can sometimes cause strange effects. At the end of the day, film that appears […]
How should I tint a window that already has a top strip?
Always remove the top strip and start from scratch. It’s best to provide your customers with 100% new film, and leaving behind an old top strip just doesn’t make sense. In addition, you can be sure you’re using top-quality films when you do the re-do the entire job.